if^jtafei^-j-^*"! ■?' — J."- „ '■'■St """s &i^^'-"T o- =1 s_. ~ QJortteU Uniuwaity ffiibrarg atljaca, Wett) fark BOUGHT WITH THE INCOME OF THE SAGE ENDOWMENT FUND THE GIFT OF HENRY W. SAGE 1691 Engineering DATE DUE MII j!) ^ ^miM 4mQ^ ^^ ^(!^i ^ ^wliu i W ^ j l tW. ^ -MH tW^ CAVLORD PIUINTED IN IJ.S A Cornell University Library VM 144.V25 A practical course in wooden boat and sh 3 1924 005 005 842 Cornell University Library The original of tliis book is in tine Cornell University Library. There are no known copyright restrictions in the United States on the use of the text. http://www.archive.org/details/cu31924005005842 A PRACTICAL COURSE m WOODEN BOAT anc/ SHIP BUILDING The Fundamental Principles and Practical Methods Described in Detail Especially Written for Carpenters and Other Wood- workers Who Desire to Engage in Boat or Ship Building, and as a Text-book for Schools By RICHARD M. VAN GAASBEEK Head of Department of Woodworking, School of Science and Technology, Pratt Institute, Brooklyn, N. Y. FULLY ILLUSTRATED CHICAGO FREDERICK J. DRAKE & COMPANY Publishers Copyright, 1918, by Frederick J. Drake & Co., Chicago Entered at Stationers' Hall, London All Rights Reserved PEEFACE To meet a popular demand for a test-book to assist the great army of house carpenters and other woodworkers in transferring from their usual occupations to the wooden boat and ship building industries, now rapidly developing in this country, and especially for those men who wish to qualify for advanced positions, and for boat and ship builders who wish to broaden their experience in order that they may prepare for greater re- sponsibilities, this work is offered. The text is the outgrowth and development of a pioneer course organized early in the war by Pratt Institute, Brooklyn, N. Y., in response to the de- mand caused by shortage of skilled labor in these industries. It was a study to know how to organize the work effectively, to select only those problems that otherwise might take years of labor in the industry for these men to solve, and to present the prob- lems progressively and in such a way that the men would grasp the basic principles in the shortest possible time. It has been the aim of the author to establish a fundamental course, — one that would help the ship builder as well as the boat builder; for whatever the size or type of the vessel, the general principles 7 8 COURSE IN WOODEN BOAT AND SHIP BUILDING of construction remain very much the same in all cases. Those who master this course can direct the labor of others, because they themselves will have learned by doing, and it is only by manipulative skill that a practical understanding of the subject can be acquired. It was out of the question to build a full-size ship. The space and equipment necessary to handle heavy timbers, the cost of the lumber itself, and the extra labor that would be required of the men after a hard day's work, were all factors to be considered in determining the kind of instruc- tion that would best meet the emergency situation. We have built a full-size boat, using full-size timbers, and, under exact factory conditions, and with the scarfing and adzing of heavy yellow-pine timbers and practice calking, both light and heavy, a course has developed, which, judging from the reports from the men as to their advance- ment and success in the industry after completing the course, has been most gratifying. The author has not attempted to give a complete treatise on the subject and therefore offers no apology for any omissions that may be found. The first part of the work (Chapters I to IV) is strictly technical in character, giving the operations in sequence as they Avere performed on the job and explaining them in such a way that the average mechanic can understand. In the second part (Chapters V to VIII) an effort is made to show PREFACE 9 typical ship construction views, giving the reader an idea of the methods of handling and fastening heavy timbers. The author wishes to express his appreciation of the generous assistance given by Messrs. Chas. Rassiga, Jr., Edward J. Weber and Harvey R. Saylor, his co-workers, and to leading wooden ship builders and manufacturers, without whose aid this work would have been impossible. Particularly the author wishes to acknowledge his indebtedness to Mr. W. G. Hudson, District Supervisor, Wood Hull Construction, Second Dis- trict, Emergency Fleet Corporation ; Mr. Theodore E. Ferris; The Foundation Company, agents of the United States Shipping Board, Emergency Fleet Corporation; Messrs. Tams, Lemoine and Crane ; Stetson Machine Works ; Messrs. J. A. Fay & Egan Company and Messrs. C. R. Durkee & Co. for permission to use the drawings and photo- graphs used in illustrating the second part of the work. The Authob. Pratt Institute, Brooklyn, N. Y. July 1, 1918. CONTENTS CHAPTER I PAGE The Mould Loft: — Sheer Plan — Half -Breadth Plan — Body Plan— Table of Offsets— Model for Taking Off OfEsets— Mould Loft Work — Laying Off— Laying Out the Sheer Plan — Laying Out the Half -Breadth Plan — Laying Out the Body Plan 17 CHAPTER II Stem and Stern Constbtiction : — The Stem — Lower Stem — Apron — Deadwood — Stern Post — Stern Post Knee — Shaft Log — Stern Deadwood — Horn Timber — Transom — Stem and Stern Moulds — Picking Up the Lines^Cutting Out the Stock — Rabbeting — Stopwaters — Keel 26 CHAPTER III Puttocks and Feames: — Futtock Moulds — Picking Up the Lines — Surmarks— Steam Box — Steam Bending — Bending Form — Diagonal Lines — Beveling Frames — Beveling Board — Frame Construction — Cross Spalls — Floor Timbers — Rais- ing Frames — Ribbands — Harpings — Fairing Up — Projection of Diagonals — Filling-in Pieces — Keelson 41 CHAPTER IV Outside Planking; — Principal Strakes — To Find the Width of Strakes— Sheer Strake — Binding Strake — Spiling — Gar- board Strake — Lower Strakes — Scaling — Beveling for Plank- ing — Calking — Finishing 68 11 12 CONTENTS CHAPTER V PAGE Ship Construction: — Materials and Processes — Drawings and Plans — Specifications — Sheer Plan — Half-Breadth Plan — Body Plan — Tables of Offsets — Midship Construction Sec- tion — Scantlings or Dimensions — Lofting the Ship — Moulds — Frames — Mill Floor Carriages — Ways 84 CHAPTER VI Machines and Labor-Saving Devices: — Sawing and Han- dling Large Timbers — Bevel and Edging Machines — Surfac- ing Knees — Faying the Knees — Working Rudder Stock — Setting Up the Keel — Assembling Platform — Fitting and Fastening Frames 110 CHAPTER VII Raising the Frames: — Work of the Riggers — Cant Frames — Bolting the Frames — Keelsons — Fairing-up Work — Iron Strapping 127 CHAPTER VIII Planking and Finishing: — Layout of the Ship — Preparations for Planking — Material — Steam Box — Clamps and Wedges — Bottom, Bilge and Side Planking — Calking — Cementing Seams and Painting — Shipfitting — Shaping the Masts — Shipyards and Ways 138 CHAPTER IX Hand Tools: — Complete List of Tools Used in Wooden Boat and Ship Building — Adze — Broad Axe — Calking Irons — Calking Mallet — Ship Auger Bits 165 CHAPTER X Wooden Boat and Ship Terminology 170 Index 199 LIST OF ILLUSTRATIONS FIGURE PAGE 1. Sheer plan — moulded lines 18 2. Half -breadth plan — moulded lines 18 3. Body plan — moulded lines 19 4. Fairing-in a line on mould loft floor 21 5. Detail of stem 27 6. Detail of stern 28 7. Moulds for stem 30 8. Moulds for stern 31 9. Picking up lines from mould loft floor 32 10. Bending battens and lining in 34 11. Fairing up moulds 35 12. Section through stem, showing the development of rabbet 36 13. Detail of rabbet. (Section through A-A, Figure 12.) . . 37 14. Erecting stem and stern and cutting rabbets 38 15. Boring through shaft log for propeller shaft 39 16. Futtook moulds forward 42 17. Futtock moulds aft 43 18. Picking up lines from mould loft floor with a flexible steel template 44 19. Details of steam box 45 20. Pipe details of steam box 46 21. Details of door of steam box 47 22. Condensation pipe and water seal trap of steam box ... 48 23. Bending timbers 51 24. Method of developing bevels on diagonals 52 25. Bevels on each diagonal 54 26. Beveling board 56 27. Sawing timbers 58 28. Fitting futtoeks to ribbands and installing frames 59 29. Manufactured frame construction — running ribbands... 61 30. Built-up frame construction 62 31. Strap frame construction 64 32. Bending frames for strap frame boat 65 13 14 LIST OF ILLUSTRATIONS FIGURE PAGE 33. Projection of diagonals on sheer plan and body plan. ... 66 34. Scaling for sheer strake 70 35. Scaling and spiling for sheer and binding strakes 72 36. Spiling for first lower strake 73 37. Scaling for binding strake 74 38. Scaling for lower strakes 77 39. Form for practice calking 80 40. Details of form for practice calking 81 41. Practice calking 82 42. Standard wooden steamship — sheer plan — moulded lines — stem 88 43. Standard wooden steamship — sheer plan — moulded lines — stern 89 44. Standard wooden steamship — half -breadth plan — moulded lines — stem 93 45. Standard wooden steamship ■ — half -breadth plan — moulded lines — stern 93 46. Standard wooden steamship — moulded lines — body plan 94-95 47. Standard wooden steamship — midship section 98-99 48. Section from bridge deck to top of wheelhouse of stand- ard wooden steamship 100 49. Section through poop 101 50. Section through engine foundation, looking forward . . . 102 51. Section through shaft tunnel, looking aft 102 52. Section through the forecastle. 103 53. Mould loft .- 104 54. Applying mould — laying out timbers 105 55. Beveling frames on the band saw 106 56. Cutting a straight timber on the band saw 107 57. Sectional carriages in mill for handling heavy timbers. . 108 58. Assembling platform ■ 109 59. Sawing a heavy timber in a modern mill Ill 60. Handling heavy timbers in the yard 112 61. Starting a cut at an angle of 11 degrees to the right. . . 114 62. Finishing the cut at an angle of 11 degrees to the left. . 115 63. The finished timber 116 64. Surfacing knees on a special machine 117 65. Faying knees on a special beveling machine 118 LIST OP ILLUSTRATIONS 15 PIGUEE PAGE 66. Shaping the rudder stock on the beveling machine 119 67. Shape of a rudder stock after sixteen cuts have been completed 120 68. The rudder stock requires but little time with hand tools to complete the work after leaving the machine 121 69. No hand tools were used in beveling the ceiling in this ship 122 70. Eecord keel laid in ten minutes in a prominent yard on the Atlantic coast 123 71. Assembling platform, showing ways and square framing 124 72. Assembling platform, showing diagonals 125 73. The frames are run on two tracks, one on either side of the ways 128 74. Frames in position ready to raise 129 75. Eaising the frame 130 76. Frames in position 131 77. These ways were lowered while the ship was in frame. . 131 78. Cant frames looking forward, showing heels of timbers 132 79. Cant frames looking aft, showing heels of timbers. . . . 133 80. Looking forward — heads of timbers 133 81. Looking aft — heads of timbers 134 82. Installing keelson 135 83. Another view of keelson and timber chute 136 84. Bow of ship ready for planking 138 85. Bow of ship planked, showing staging 139 86. Close-up view of ship, showing detail of bow construction 140 87. Wooden ship framed up complete, ready for planking. . 141 88. Partially planked 142 89. Planked ready for launching 143 90. The finished ship 145 91. Stern of ship showing vertical planking 146 92. Interior of hull, looking aft 147 93. View of ^framing platform 148 94. Eeady to launch 149 95. Framing the poop deck 150 96. Poop deck completed 150 97. Eaising the rudder 151 98. Shaping the masts 151 16 LIST OP ILLUSTRATIONS FIGTJRE PAGE 99. Panoramic view of a prominent shipyard on the At- lantic coast 152 100. Continuation to the left of shipyard scene in Figure 93. 153 101. Inboard profile of standard wood steamship for the U. S. Shipping Board 155 102. Wheel-house and navigating bridge 156 103. Top of wheel-house 157 104. Boat deck, standard wood steamship 158 105. Top of gun house 159 106. Poop deck 159 107. Bridge deck, standard wood steamship 160 108. Forecastle deck 161 109. Section through engine room, looking forward 112 110. Section through boiler room, looking aft 163 111. Plan view at dynamo flat and engineer's storeroom. . . . 164 112. Plain adze 167 113. Lipped adze 167 114. Scarfing timber with adze 167 115. Broad axe 168 116. Dumb or deck iron 168 117. Calking or making iron 168 118. Calking mallet 168 119. Ship auger bit 168 TABLES 1. Table of Offsets, Wooden Boat 22-23 2. Table of Offsets, Standard Wooden Steamship — Heights Above Base 90 3. Table of Offsets, Standard Wooden Steamship — Diag- onals 91 4. Table of Offsets, Standard Wooden Steamship — Half- breadths , 92 A PRACTICAL COURSE IN WOODEN BOAT AND SHIP BUILDING CHAPTER I THE MOULD LOFT The principal drawing of a vessel is the sheer drawing. It is composed of three parts, mutually dependent upon each other, as follows : Sheer Plan. — Figure 1. — A side view showing length of vessel and heights of sheer or gunwale. Half-breadth Plan. — Figure 2. — A top view, showing a horizontal or floor plan on any water lines. Body Plan. — Figure 3. — An end view, showing curves of the frame line's outside the timber at any point in the vessel. Frame lines forward of the midship section are on the right of the center line ; aft of the midship section on the left of the center line. TABLE OF OFFSETS The table of offsets exhibits the distances from a center or base line. These offsets are compiled by the naval architect and are used by the mould loftsman in laying down the lines on the floor. Just how these offsets are compiled is only of pass- 17 18 COUESE IN WOODEN BOAT ANB SHIP BUILDING .g 1 a Hi THE MOULD LOFT 19 ing interest to the reader, as it is the purpose of this work to help the mechanic to apply them. Model for Taking Off Offsets. — The most prac- tical way of taking off the offsets is to make a model of wood, an invention of an American mechanic. The model must be made to an exact O «(> (0 w ro 't 10 vj y l3 5 i w tn «o Figure 3. — Body Plan — Moulded Lines. scale, usually i^" to 1', and it is generally com- posed of two kinds of soft wood of different colors, such as pine and cedar, in alternate layers screwed or pinned together. The seams between the layers represent the water lines. The model usually represents the starboard half of the vessel and has a plane side, represent- 20 COURSE IN WOODEN BOAT AND SHIP BUILDING ing the longitudinal midship plane, on which the sheer plan is drawn. Its curved side is then grad- ually carved, shaved, and filed to such a form as to satisfy the eye and the judgment of the designer. It is very important, in making the model, to fair up perfectly every portion, so that one portion of it assimilates with the other. If the model is made to a small scale, the discrepancies can be more readily detected, because the whole of the model can be seen at a glance and the inequalities of one end as compared with the other will be dis- covered. The model must be perfectly fair, not only on all lines, but in every direction. Station lines, rabbet line and bearding line, and all water lines are laid off to the same scale on the model. The layers can then be separated and from these the table of offsets is scaled. The accuracy with which the model is scaled will save the time of the mould loftsman in laying down his lines. MOULD LOFT WORK Laying Off of the Lines. — The laying off of the lines on the mould loft floor can be compared with the foreman's layout in carpenter work. (See Figure 4.) It is the name given to the process of drawing the lines of a vessel to full size in plan and elevation, in order to determine the exact dimensions of the most important and fundamental parts of the structure. The necessity for drawing to full size arises from the extreme accuracy with which the dimensions of the various parts must THE MOULD LOFT 21 correspond with one another in order that when assembled there may be no irregularity or unfair- ness in the surface of the vessel. If the mould loft is not long enough for laying down the vessel full length, it can be laid doAvn in WBtKBA 1^^ w Y^f^^^^^^^^l HIHI ^ 1 1^ n lifl ^S H V ' WS^ - 1 f i - 1 . I ■ , j^^jH i Figure 4. — Fairing-ln a Line on Mould Loft Floor. sections, one overlapping the other, providing the sections are long enough to properly fair up the lines. If the vessel is very large, this is an impor- tant operation, for while looking at one part of the line, it may be impossible to see the other side of the same line. Figure 4 shows a section of the 22 COURSE IN WOODEN BOAT AND SHIP BUILDING TABLE OF OFFSETS Water Lines Spaced 3 Inches Stations Spaced 12 Center Line to Center Line Section Lines Spaced 3 Inches Stem 2-2-0 1 2 3 4 Height of Gunwale Above Base. , 1-11-6 i 0- 0-3 0-10-0 1-9-5 1-7-7 + 1-6-5 Balf-Breadth of Gunwale.. 1-4-2 1-7-2 1-8-2 Half-Breadth of Water Line No. 1 0-2-1 + 0-3-5 + 0-4-7 0-5-7 0-6-5 0-7-5 0- 5^ + 0-8-4 0-10-3 0-11-6 1- 1-1 1-2-3 0-8-7 1-0-6 1-2-7 1-4-2 + 1-5^ 1-6-4 + 0-11-6+ Half-Breadth of Water Line No. 2 1- 4-0 Half -Breadth of Water Line No. 3 1- 5-7 + Half-Breadth of Water Line No. 4 1- 7-1 Half-Breadth of Water Line No. 5 1- 7-6 Half-Breadth of Water Line No. 6 1- 8-1 + Height of Sec. No. 1 Above Base 0-4-4 0-1-3 1-9-4 0-1-3 + 0-3-3 0-6-5 0-1-3 1-7-0+ 0-0-7 + 0-1-6 0-3-1 0-5-1 0-9-1 1-4-2 0-0-6 Height of Sec. No. 2 Above Base 0-1-2 + Height of Sec. No. 3 Above Base 0-2-0 Height of Sec No 4 Above Base 0-3-0 + Height of Sec. No. 5 Above Base 0-5-0 Height of Sec. No. 6 Above Base 0-9-1 Base Line W.L.I W. L. 2 • W. L. 3 W.L.4 EabbetfromF.P Habbet from A P 1- 5-6 2-10-4 0-6-7 - 0-5-5 1-5-0+ 0-2-3 0-3-0 0-9-7 + 0-1-0 1- 0-2-2 0-4-4 0-0-4 0-1-7 Tore Edge of Stem From F. P. . . 0-0-1 + mould loft floor at Pratt Institute, Brooklyn, N. Y. The men are f airing-in a line, as can be seen ; that is, making its curve true and regular. A mechan- ical eye will save a great deal of labor, for much depends upon the fairing-in of the lines, as con- siderable injury may be done to a good design by deviating from the drawings. THE SHEEK PLAN To lay off the sheer plan, Figure 1, first produce the base line and run the water lines in parallel THE MOULD LOFT TABLE OF OFFSETS 23 Stations Spaced 12 Center Line to Center Line 5 6 7 8 9 10 11 Tranaom 1-5-7 1-5^ + 1-5-4 1-5-6 1-6-1 + 1-7-0 + 0-1-1 + 1-6-5 1-8-H- 0-5-0 1-5-0 + 1-9-6 0-11-5 1-8-4+ 1-8-5 1-8^ + 1-8-1 + 1-7-4 + 1-2-6 1-2-1 + 1-3-4 1-7-2 1-8-3 1-8-4 1-8-5 1-3-4 1-7-2 + 1-8-2 + 1-8-4 1-8-4 1-1-7 1-6-3 + 1-7-7 1-8-1 1-8-1 + 0-10-2-1- 1-4-3 1- 6-5-1- 1- 7-3 -r 1- 7-4-1- 1- 7-4 T 0- 4-5 0-11-6 + 1-3-6 1-6-0 + 1- 6-4 r 1- 6-5 1-6-1 + 0-2-5 0-9-3 1-2-1 1-4-2 1^-7 + 1-7-5+ l^S-2 1-8-4 0- 1-7+ 0-10-1 + 1- 1-6 + 0-0-5 + 0-1-1 0-1-5 0-2-2 0-3-2 + 0-5-6 0-0-5 0-1-0 0-1-3 0-1-7 0-2-6 0-4-3 0-0-5 + 0-1-0+ 0-1-3 + 0-1-7 + 0-2-6 + 0-4^ 0-0-6 0-1-1 0-1-6 0-2-3 0-3-4 0-5-4 0-0-7 + 0-1-6 0-2-4+ 0-3-5 0-5-0 0-7-7+ 0-2-3 0-3-4 0-4-5 0-6-1 0-8-0 1-0-0 0- 6-1 0- 7-3 0- 8-6 1-10-4 1- 0-7 1-0-2 + 1-1-2 + 1-2-3 1^-0 + W. L. 5 W. L. 6 Sheer 0-1-6 0-1-6 0-1-6 0-0-1 0-0-1 0-0-1 to the base line. Then strike in the station lines at right angles to the base line and equidistant apart. The method of laying down one or two lines will suffice to give the reader enough information to enable him to complete the layout. We will assume that the vessel has been outlined and will therefore lay off the sheer line and section 5. To lay out the sheer line refer to top line of the table of offsets. This gives the heights of gunwale or sheer above the base line. Point off these dis- 24 COURSE IN WOODEN BOAT AND SHIP BUILDING tances on the various stations from the base line. The first figure represents feet, the second inches, and the third eighths, as follows : At the stem, 2' 2" ; on station 1, 1' 11 6/8" ; sta- tion 2, 1' 9%" ; station 3, 1' Vk" ; station 4, V 6%" ; station 5, 1' 5ys"; station 6, 1' 5 4/8"; station 7, r 5 4/8"; station 8, V 5 6/8"; station 9, 1' ei/g"; station 10, V 7" ; station 11, V 8ys", and at the tran- som, r 9 6/8". Drive a small nail in at these points and bend a thin batten so as to approximate as closely to these points as is consistent with absolute fairness and continuity. If the batten does not spring well to these points, it is best to pass the batten inside some and outside others in order to prevent great deviation from the design in either direction. Likewise refer to section 5 on the sheer plan and height of section 5 above base in the table of offsets. Point off on each station line as shown, namely, station 2, 1' 7"; station 3, 0' 91/3"; station 4, 0' 5"; station 5, 0' 3 2/8"; station 6, 0' 2 6/8"; station 7, 0' 2 6/8"; station 8, 0' 3 4/8"; station 9, 0' 5"; sta- tion 10, 0' 8", and station 11, 1' Oyg". Drive a small nail in at these points and bend a thin batten through them as described in the preceding para- graph. HALF-BKEADTH PLAN To lay off the half -breadth plan. Figure 2, strike a line representing the center line and mark in the stations of the frames as shown. Set up from the- THE MOULD LOFT 25 center line on the various stations the half -breadths of the water lines and sheer lines, taking the dis- tance from the table of offsets. The method of laying down the half -breadths of water line No. 2 will show the reader enough to enable him to complete the layout. Eefer to the table of offsets, half-breadth of water line No. 2. Point off these distances on the various stations from the center line, namely, on frame 1, 3%"; frame 2, 8 4/8"; frame 3, 1' 6/8"; frame 4, T 4"; frame 5, 1' Gi/s"; frame 6, 1' 7 2/8"; frame 7, r 7 2/8"; frame 8, 1' 6%"; frame 9, 1' 43/s"; frame 10, 0' 11 6/8" ; frame 11, 0' 2%". Drive small nails at these points, and bend a thin batten through them, passing it inside some and outside others as need be in order to properly fair up the lines, as explained in a previous paragraph. BODY PLAN To lay off the body plan, Figure 3, first produce the base line and then the center line. Lay off the water lines parallel to the base line and the station lines parallel to the center line. Scale off from these lines on the drawing the various frame lines and transfer these locations to the mould loft floor, taking all measurements from the corre- sponding line. Drive in small nails at these points and bend a thin batten, fairing up the line as may be required before striking in the line. CHAPTER II STEM AND STEKN CONSTKUCTION The stem is made up of four members, namely, Stem, Lower Stem, Apron, and Deadwood. The stern is made up of six members, Stern Post, Stern Post Knee, Shaft Log, Deadwood, Horn Timber and Transom. Stem. — The stem (Figure 5) is the foremost boundary of the boat, being a continuation of the keel to the height of the vessel, at the fore extremity. Loiver Stem. — The lower stem is a curved piece placed in the angle formed by the apron and the upper end of the deadwood. Apron. — The apron is the upper member of the stem on the inboard side of the boat. It is intended to strengthen the stem and afford wood for the reception of the outside planking and the heels of the foremost timber. Deadwood. — The deadwood is the lower member of the stem on the inboard side of the boat. The deadwood becomes the foundation against which the heels of the forward frames are abutted. Stern Post. — The stern post (Figure 6) forms the after boundary of the frame of the boat, being the after continuation of the keel to the height of 26 STEM AND STERN CONSTRUCTION 27 I? Si' 28 COURSE IN WOODEN BOAT AND SHIP BUILDING STEM AND STERN CONSTRUCTION 29 the deck, and forms a receptacle for the after ends of the outside planking. Stern Post Knee. — The stern post knee is placed in the angle formed by the keel and stern post. Shaft Log. — The shaft log is the member of the stern through which the propeller shaft enters. Deadwood. — The deadwood is the lowest mem- ber of the stern, run up to the height of the floor timbers, and on it the after ends of the keelson rest. Horn Timber. — The horn timber protects the end of the stern post and covers up the end wood. Transom. — The transom is the last main frame of the boat and is placed square with the stern post. These members of the stem and stern are united to each other and to the fore and after ends of the keel by scarfs, bolted together. STEM AND STEKN MOULDS It is necessary to make a separate mould, or pat- tern, for each member of the stem, Figure 7, and the stern. Figure 8, on which all construction lines are transferred from the mould loft floor. These moulds are needed in locating bearding and rabbet lines and locating various points such as water lines, etc., used in setting up the timbers and fair- ing the structure. Accuracy in making the moulds is very necessary, in order to insure the economical appropriation of timber and to facilitate the execu- tion of the workmanship. Picking Up the Lines. — A simple method of 30 COURSE IN WOODEN BOAT AND SHIP BUILDING Figure 7.— Moulds for Stem. STEM AND STERN CONSTKDCTION 31 picking up the lines is shown in Figures 9 and 10. On the floor is shown the full size layout of the stem and stern construction shown in Figures 5 and 6. Place a series of tacks with the heads resting Figure 8. — Moulds for Stern. on the required line, Figure 9. The heads of the tacks should be driven into the floor slightly, to prevent them from moving out of place. Place a piece of stock wide enough to cover the member, with the grain of the wood running in the direction that will show the least amount of end wood (to prevent splitting when cut to shape). Give the mould several light taps with the hammer in the direction of the curve. The heads of the 32 COURSE IN WOODEN BOAT AND SHIP BDILDINQ ¥SKj ""^^ mgM/ge^^MjiMM '''/■'t^-f-- ■i,:^^ :, ■\- ^^ ■i ^ : ;:-;l M 1^91 P 9 ^-^sltoiste k 5 STEM AND STERN CONSTRUCTION 33 tacks will leave a mark into which a small brad can be driven and around which a batten can be bent. See Figure 10. Saw the moulds on the band saw, leaving the lines full, and fair up by hand as shown in Figure 11, making a perfect fit of each piece. Transfer the water lines and all construction lines from the floor to the mould, when the moulds will be ready for use. The moulds are generally made of one-half inch pine. The stock for the stem, as shown in the de- tail, calls for 11/2" stock for all members except the apron, which is 21/0" material, and all members of the stern 2i/^" stock, excepting the horn timber, which is II/2" thick. Cutting Out the Stock. — Apply the moulds to the stock to be used in the construction of the boat, and cut out the stock on the band saw, leaving the lines full for fairing up. If the moulds have been accurately shaped and fitted, the stock to be used can be lined up to these moulds and fitted without much trouble. They can now be riveted or bolted together. RABBETING It is usual and proper to cut the rabbet, or recess in the stem and stern to receive the ends of the planking, before raising them. The bearding line, or liae formed by the curved surface of the vessel's planking with the stem, keel, and stern post, and the rabbet, or outside line of the planking, are 34 COURSE IN WOODEN BOAT AND SHIP BUILDING STEM AND STERN CONSTEUCTION Figure 11. — Fairing Up Moulds. 36 COURSE IN WOODEN BOAT AND SHIP BUILDING s STEM AND STERN CONSTRUCTION 37 transferred from the moulds to the stem and stern, and the rabbet is cut in with a chisel. A section through the stem is shown in Figure 12 and a full-size detail of the rabbet is shown in Figure 13, the line A-B, Figure 13, representing the bearding line, and the line C-D the rabbet line. E-P is the width of the rabbet on the first water line, as shown on the projection, Figure 12, and is Figure 13. — Detail of Rabbet. (Section Through A-A, Figure 12.) formed by the intersection of the bearding, rabbet, and first water lines. Make a template or mould the thickness of the planking, as shown at G, about l^o" wide and 3" long, depending upon the size of the rabbet to be cut. Bevel one end as shown, about i/s" in 1". Begin chiseling at the rabbet line to the bevel of the mould, and cut from the bearding line until the mould rests in the rabbet. Figure 14. The 38 COURSE IN WOODEN BOAT AND SHIP BUILDING STEM AND STERN CONSTRUCTION 39 Figure 15. — Boring Tlirougli Sliaft Log for Propeller Shaft. 40 COURSE IN WOODEN BOAT AND SHIP BUILDING mould being the same thickness as the planking, the outside edge must intersect at F, or on the rabbet line. Stopwaters. — The stopwaters, or round pieces of wood or dowels, are driven in at all seams run- ning inboard, to render the vessel watertight. KEEL The keel, forming as it does the lower boundary of the longitudinal section, is spoken of as the back- bone of the vessel. The pieces are obtained in as long lengths as possible, varying in size according to the size of the vessel. The several pieces forming the keel are joined together by lock scarfs and also scarfed to the stem and stern, bolted and riveted together. A chalk line is run from the center of the stem and stern for the purpose of lining them up with the center of the keel. The rabbet extends along the keel to receive the edge of the first strake of planking, or garboard strake. Station lines are marked upon the top of the keel, giving the location of the various frames. See Figure 14. Shaft Log. — As soon as the stem and stern are plumbed and united to the keel, the opening for the propeller shaft should be bored through the shaft log. Figure 15. The line of the shaft is laid out from the mould. The bit is held in position as shown in the illustration to insure the proper direc- tion. CHAPTER III rUTTOCKS AND FRAMES The futtocks, commonly called the ribs of the vessel, are the curved or crooked timbers giving the shape, to which the planking is fastened. Two futtocks united, right and left hand, constitute a frame. FXJTTOCK MOULDS A mould should be made of each futtock of a different shape. Futtock moulds forward are shown in Figure 16. Futtock moulds aft are shown in Figure 17. The method of picking up the lines from the mould loft floor is similar to the one described for picking up the lines of the stem and stern con- struction. Another method is shown in Figure 18, using a flexible steel template. This template can be bent to any shape and is held in position by winged nut screws on the outside. Adjusting the template to the required shape on the mould loft floor, and fastening the screws, the template can be taken up and used in lining the stock to be cut. The shape of the futtocks is taken from the body 41 Fisuro 10.— Futtock Moulds Forward. u:^ w r^j? <9 Figure 17. — Futtock Moulds Aft. u COURSE IN WOODEN BOAT AND SHIP BUILDING plan, Figure 3. These lines give the outside lines of the frames. The width of the frames will de- pend largely upon the size and the demands to be made upon the vessel. Figure IS. — Picking Up Lines from Mould Loft Floor with a Flexible Steel Template. Cut the moulds full of the line to allow for fair- ing up, finishing the mould by hand. Each mould is numbered so it can readily be placed in its proper location. FUTTOCKS AND FRAMES 45 i 4e COURSE IN WOODEN BOAT AND SHIP BUILDING The sheer, diagonal, and keel lines are trans- ferred from the floor to the moulds. These lines will be needed in lining up and setting the frames^ and for locating the beveling spots and running- the ribbands. Surmarks. — The marks on the moulds showing Figure 20. — Pipe Details of Steam Box. the intermediate bevel stations, or where the diag- onal lines cross the futtocks, are called surmarks. STEAM BOX The futtocks, ends of ribbands, and planking will need to be steamed in order to bend them ta the required shape. The size of the steam box required is dependent upon the size of the timbers, and planking to be bent. Details of a steam box are shown in Figures 19,. 20, 21 and 22. The dimensions can be varied, either enlarged or made smaller, to meet a special need. FUTTOCKS AND FRAMES 47 The box is made of cypress with butted joints and calked seams. Cleats continue around all four sides, bolted together. The steam enters at one end and runs through a perforated pipe the entire length of the box, which distributes the steam and gives an even tem- perature throughout. At the front end a small Figure 21. — Detail of Door of Steam Box. vent pipe takes off the surplus steam and leads it out doors. At the far end there is an outlet for the condensation, leading to a water seal trap, shown in Figure 22. The water lying in the trap prevents the steam from escaping. The condensation can be drained into a pail or connected with the sewer if desired. If the steam box is located out of doors, the con- densation will take care of itself, as it can run off into the earth and the steam can escape and pass. 48 COURSE IN WOODEN BOAT AND SHIP BUILDING off in the atmosphere. If the steam box is located indoors, some provision of this kind should be «yrj CL03ei/Mv£-r Figure 22. — Condensation Pipe and Water Seal Trap of Steam Box. made for taking care of the condensation and sur- plus steam. Packing is placed in the rabbet of the door to FUTTOCKS AND FRAMES 49 make it tight, the door locking with an ice-box fastener. STEAM BENDING Special bending stock should be used. Green or unseasoned lumber bends more readily and is not so liable to split while being bent as seasoned stock is. It would be better to put the stock into a water bath for several hours or overnight before steaming it. The stock should be thick enough to make two futtocks, and when removed from the form should be resawed, making right and left hand futtocks, which, when fastened together, make a complete frame. The futtocks being thicker at the heel, some material can be saved and the stock will bend easier if the timbers are tapered. Experience is the best teacher as to the length of time required to steam a piece of stock ready for bending. The greener or wetter the stock, the shorter the time required. If the stock is left in the box too long, the life is taken out of the timber and it becomes very brittle and breaks ; while, on the other hand, if not left in the steam box long- enough, the timber will also break. STEAM BENDING FORM A bending form is shown in Figure 23. The shape of the form should be made from the inside line of the moulds, and an extra allowance made for shaping and fitting, as well as for some spring in the timber when removed from the form. In 50 COURSE IN WOODEN BOAT AND SHIP BUILDING other words, the form should be made to a quicker sweep than the moulds. Wlien the stock is ready to be bent, one piece is removed at a time from the steam box and a thin sheet of strap iron is nailed on the back of the timber, to give support to it while being bent and to insure a fairer bend. As soon as this strap iron is fastened, one end is inserted under the bar, as shown in the illustra- tion, and held in position by a wedge. One man bends the timber around the form and another man pulls it into place with a clamp. The timber will retain the heat for some time, so there is nothing to be gained in forcing it to the breaking point. As the timber is bent around the form, clamps are applied at intervals to give added support to the stock while bending. The end of the timber is held in place by a hook, which catches over an iron pipe extending tlae full width of the form. This can be seen in the lower right-hand corner of the form (Figure 23). The timbers should set a day before being re- moved from the form, Avhen they can be resawed and planed to the required thickness. Line up the timbers from the moulds and number each one for ready identification. DIAGONAL LINES The diagonal lines are dra-\vn in on the body plan. Figure 3, standing as nearly square as pos- FUTTOCKS AND FRAMES 51 sible to the frame lines. They are considered the most effectual toward fairing the body of the ves- sel, or making each portion of the vessel assimilate with the others. The diagonals are distinguished Figure 23. — Bending Timbers. as "1st, 2nd, 3rd, etc., diagonals," and give the stations or surmarks of the ribbands, which are placed around the timbers to give support to the vessel while in frame. 52 COURSE IN WOODEN BOAT AND SHIP BUILDING SHCER Line Sheer Line. MM Figure 24. — Method of Developing Bevels on Diagonals. FDTTOCKS AND FRAMES BEVELING FRAMES The edges of the frames must be beveled, so that when the planking is bent around them they will fit tight at all points. These bevels are developed on the diagonal lines, as shown in Figure 24. Draw two lines at right angles to each other. Point off a distance on the vertical line equal to the distance between frames, center to center. On the horizontal line point off from the intersection of these two lines the distance between frames 7 and 8 on the second diagonal, then the distance between frames 8 and 9, the distance between frames 9 and 10, the distance between frames 10 and 11 and the distance between frame 11 and the transom. All measurements are to be taken on the second diagonal between frames, and all measured off from the intersection of the vertical and horizontal lines. Connect these points with the point on the vertical line, as shown in the illustration. Then bevel F is the bevel for frame 8, bevel G is the bevel for frame 9, bevel H is the bevel for frame 10, bevel I is the bevel for frame 11, and bevel J is the bevel for the transom. All bevels are developed on the second diagonal. Likewise with the forward frames. Draw two lines at right angles to each other, as shown to the left in Figure 24. On the vertical line measure off a distance equal to the distance between frames, center to center. On the horizontal line point off from the intersection of these two lines the distance 54 COURSE IN WOODEN BOAT AND SHIP BUILDING FUTTOCKS AND FRAMES 55 between frames 5 and 6 on the second diagonal; then the distance between frames 4 and 5, the dis- tance between frames 3 and 4, the distance between frames 2 and 3, and the distance between frames 1 and 2. All measurements are to be taken on the second diagonal between frames and all measured off from the intersection of the vertical and horizontal lines. Connect these points with the point on the vertical, as shown in the illustration. Then bevel A is the bevel for frame 1, bevel B is the bevel for frame 2, bevel C is the bevel for frame 3, bevel D is the bevel for frame 4, and bevel E is the bevel for frame 5. Frames 6 and 7 are amidship and are square. Bevels are developed on each diagonal as shown in Figure 25. Therefore, in this particular boat, each frame has four bevels, namely, sheer, 1st, 2nd and 3rd diagonals, one fairing into the other. BEVELING BOARD The mould loftsman makes a beveling board, as shown in Figure 26, giving the various bevels. These bevels are taken from the developments, Figure 25. This saves time, referring to the mould loft, when laying out the frames, as it gives all the bevels needed for the entire vessel. In many yards, and especially in ship work, the bevels are spoken of as degrees, and are so listed on the beveling board. This is for the information of the mechanic operating the band saw, as he tilts his saw one way or another to a desired angle, BEVELS 3">DMa. Men 1 2 JL 1 i 1 23456789 10 11 Figure 37. — Scaling for Binding Strake. the dividers on this line, point off equal distances ■on the spiling batten, as shown in Figure 35. This gives the points for the upper edge of the binding strake. Lay the spiling batten on the stock to be cut for the plank, mark the spiling spots, and transfer these points from the spiling batten to the plank to be cut. This strake will be narrower than the sheer strake and it will be necessary to scale again for the lower edge, to get a fair diminish fore and aft. OUTSIDE PLANKING 75 Scribe another circle, as shown in Fignire 37, with a radius equal to the desired width of the plank on the midship frame, and strike a center line. Measure up, at right angles from the center line, a distance equal to the width of the plank at frame 1, until it cuts the circle as at L. Likewise measure up, at right angles to the center line, a distance equal to the width of the plank at frame 11, until it cuts the circle as at F. Divide equally the distance between these two lines on the center line into as many spaces as there are frames, and lay off parallel lines as shown. Then the distance L is the width of the plank at frame 1, M width at frame 2, N width at frame 3, width at frame 4, P width at frame 5, Q width at frame 6, R width at frame 7, 8 width at frame 8, T width at frame 9, U width at frame 10, V width at frame 11. Lay off these distances from the spiling spots on the plank to be cut, as shown in Figure 35. Bend a batten through these points, which will give a fair diminish and the shape of the binding strake. After the plank is sawed and fitted, a mate can be lined out for the other side of the boat before it is fastened. GAEBOAED STEAKS After determining the width of the garboard strake at midship and fore and aft, run a ribband on the frames for the top edge of the garboard, which should look fair from all directions. It is 76 COURSE IN WOODEN BOAT AND SHIP BUILDING important to have a proper diminisli fore and aft, to avoid trouble in installing the shutter strake. Bend a thin spiling batten around the frames to approximate the position of the garboard, and take a spiling for the lower edge, as previously described. Where the rabbet rounds up into the stem and stern, the spilings should be closer to- gether and square out from the rabbet. Transfer these points from the spiling batten to the stock to be used for the plank, and bend a thin batten through these points. Measure up from the rabbet to the ribband or top edge of the garboard at each frame. Transfer these distances from correspond- ing positions on the plank, and bend a batten through these points, which give the shape of the garboard. LOWER STKAKES After the binding strake and garboard are in- stalled, take the girth of the midship frame between these two planks and divide the distance into the number of planks desired to side in the remainder of the boat. Likewise take the girth on frame 1 and frame 11 and divide these distances by the number of planks in order to find the width of each plank fore and aft. A spiling must be taken for the top edge of each plank and the lower edge must be scaled to get a fair diminish fore and aft, bring- ing out as it does the parallel longitudinal lines of the boat. OUTSIDE PLANKING 77 78 COURSE IN WOODEN BOAT AND SHIP BUILDING SCALING Bend a thin batten around the midship frame to get the girth or distance between the garboard and binding strake as shown in Figure 38, A-B. Like- wise take the girth between the same points on frame 1, C-D. Square these two points across the batten, E-F, and divide the space up into as many equal parts as there are eighths contained in the difference between the width of thfe plank at mid- ship and the desired width at the stem. Assume that the width of the plank is to be 3" amidship and 2-2, or 2 2/8", at the stem. The dif- ference between 3" and 2 2/8" is 6 eighths ; there- fore, divide the difference in the girth of the mid- ship frame, or frame 6, and the girth, or frame 1, into 6 equal parts, as shown in FigTire 38, E-F. Mark the distance of the girth of the midship frame on the batten 3", the distance of the girth of frame 1, 2-2. Each division is then numbered 2-3, 2-4, 2-5, 2-6, 2-7. It will readily be seen that wherever this scale is applied with the lower edge of the batten always resting against the upper edge of the garboard, it immediately gives the width of the plank at that particular point. The width at each spiling station should be scaled and marked on the strake for ready reference. This gives a fair diminish for the plank on the forward end only. The after end is then scaled in a similar manner, as shown in FigTire 38. Take the width of the plank OUTSIDE PLANKING 79- at midship, as previously described, as 3", and assume that the width of the plank at frame 11 is to be 1-7 or 1-%"- The difference between 3" and 1-%" is 9 eighths. Divide the difference in the girth of the midship frame and the girth of frame 11 into 9 equal parts, as shown at I-J. Call the girth of the midship frame 3" and the girth of frame 11 1-%", and succeeding distances 2-0, 2-1,, 2-2, 2-3, 2-4, 2-5, 2-6, 2-7, 3-0. This immediately gives the width of the plank at that particular point. Scale each spiling station as before and mark on the strake for ready reference. With the width thus determined, it is of course unnecessary to run ribbands on the frames, unless it appears that the strakes are not running fair, but a spiling must be taken for the upper edge of each plank. If the frames are curved, it may be necessary to hollow the inside of the planking to- fit. BEVELING FOE PLANKING The planking should be beveled square from the diagonals. At the bottom edges of the seams the planks should be in contact throughout their length. After the planks are fitted, the outer edge should be beveled about 1/16" in 1", beveling from about the center of the plank. If the openings of the seams were of equal width throughout their depth between the planks, it would be impossible to make the calking sufficiently compact to resist the water. 80 COURSE IN WOODEN BOAT AND SHIP BUILDING CALKING Before beginning to calk, all seams should be jacked off and all high spots removed. Begin calk- T -8-tf' lb -fOi t? E3> f&M^ Iron Bolts-I3"long^ lO "do €" i 4 .4 All material used To Be: Yellow Pine. Figure 39. — Form for Practice Calking. ing at one end and tuck a strand of cotton or oakum into the seam, then with a dumb iron gather the OUTSIDE PLANKING 81 cotton or oakum into a small loop and drive it in ; then another loop, and so on along the seam, vary- ing the size of the loop to make just the right body of cotton or oakum to properly fill the seam. Figure 40.- enlarge.d section at Showing Fastcnings, Calking Seams And Plugs Over nails. -Details of Form for Practice Calking. Go over the seam again, using a calking iron, and drive the cotton or oakum home, so that room is left for the reception of the putty. The tendency of the amateur is to drive the 82 COURSE IN WOODEN BOAT AND SHIP BUILDING oakum into the planking instead of into the seam. This is very injurious and leads to leakage and to the rotting of the planks themselves. Figure 41. — Practice Callcing A suitable calking form for practice calking is shown in Figures 39-40. In Figure 41 two men are seen calking. Experience is the best teacher, and so it is worth while to begin practicing on a form OUTSIDE PLANKINO S» of this kind. This form can be made collapsible^ and the calking readily removed for recalking. FINISHING After calking, the seams are painted with a moderately thick paint, working it in well, so that it covers the calking material and serves as a binder for the putty. A special narrow brush,, called a seam brush, is made for the purpose. After the paint is dry, the planking should again be planed, using a smoothing plane, with the iron. set very fine. It should then be sandpapered, first across the grain and then with the grain. All unfair places will be very conspicuous after paint- ing, so it is very important that particular care be used at this time. The seams are then filled with putty, flush with the outside, and again sandpapered, ready for the painter. CHAPTER V SHIP CONSTEUCTION MATERIALS AND PEOCBSSES Practical sliipbuilding requires a knowledge of the properties of the materials used in the con- struction of ships, and of the processes by which they are produced or prepared for use, so that they may be suitably selected for the services for which they were intended. It also requires a knowledge of the methods, means, and machinery by which, after delivery in the shipyards, the materials are brought to the required shape, erected in their proper relative position, connected together, and completed so as to form a structure which will fulfill the intentions of the designer. There is an ever-increasing demand for rapid production. The revival of the wooden shipbuild- ing industry necessitates a vigorous and constant search for simplification of methods of work, for labor-saving and time-saving machinery, and for improved means of handling materials. The shortage of skilled carpenters has caused engineering departments to design and construct new machines to take the place of men working on certain parts of a vessel, thus releasing a great many men for other work, where they can be used to better advantage. 84 SHIP CONSTRUCTION 85 In previous chapters the methods of laying- down the lines and developing bevels, scaling, spil- ing, etc., have been taken up in detail. In the following chapters special attention is given to the methods of handling and fastening the large tirn- bers used in ship construction. Drawings and Plans. — The larger the vessel the more details there are to be considered. In the building of the standard wooden cargo carriers, now being built for the United States Shipping Board by the Emergency Fleet Corporation (photographs of Avhich illustrate the greater part of this text) numerous drawings are required be- fore the completion of the vessel. Drawings must be made showing the general arrangement of decks, lower hold, inboard profile^ midship construction section, together with lines and offsets for lofting the vessel, and framing plans. During the progress of the work plans are also required to show the drainage, heating,, plumbing, sanitary system, steering gear, masts, rigging, cargo gear, electric light arrangement and wiring, together with all necessary detail hull plans. Specifications. — The specifications are part and parcel of the drawings. They give a statement of all the particulars of the ship, including what is shown on the drawings as well as what cannot be shown on them. The quality of the rnaterials to be used is described in detail and the scantlings, or dimensions, of the same are carefully recorded. 86 COURSE IN WOODEN BOAT AND SHIP BUILDING It is also clearly stated how parts not manufac- tured by the shipbuilder are to be obtained. Any omissions in the specifications, or in the drawings, the absence of which from the construc- tion of the vessel would be weakening or detri- mental, must be furnished by the builder. The specifications are prepared by the naval architect, but this last clause serves as a check upon him. The decision, in all cases of doubt aris- ing, rests with the architect. Sheer Plan. — FigTires 42 and 43 give the sheer plan, or outside form of the ship, stem and stern portions, respectively. The sheer plan consists of an elevation showing the longitudinal contour, the water lines or lines at which the vessel will float, and certain other lines parallel to this and equally spaced below it, which are also called water lines. A series of vertical lines equally spaced from stem to stern, called square stations, and cer- tain other details are included in the sheer plan. The necessary tables of offsets are also given. TABLES OF OFFSETS Preliminary offsets of standard wooden steam- ships are given in the accompanying tables, for half-breadths, heights above base, and diagonals, respectively. All offset figures in these tables are to the out- side of frame (inside of plank, and are given in feet, inches, and eighths). Note that the vertical sections are spaced 13 SHIP CONSTRUCTION 87 feet apart ; buttocks and bowlines 2 feet 6 inches apart; diagonals and water lines spaced as per body plan. Dimensions. — The dimensions of the standard steamship are as follows : Length on deck 281'-6" Length bet. perpendiculars. . . 268'-0" Breadth moulded 45'-2" Depth moulded at side 26'-0" Designed load draft (full) . . . 23'-6" Half -breadth Plan. — Figures 44 and 45 give the half-breadth plan, showing the form of the ship at the several water lines, supposing the hull to be cut by horizontal planes at the level of these water lines. Body Plan. — Figure 46 shows the sectional form of the ship at the square stations, supposing the hull to be cut by transverse planes at these stations. The table of offsets required follows the body plan. Midship Construction Section. — Figures 47 to 52 show the structural arrangement of the ship and scantlings of the most important parts. The mid- ship construction section is shown in detail in FigTire 47, while miscellaneous sections appear in Figures 48, 49, 50, 51 and 52. Figure 48 shows a section from the bridge deck to top of the wheel house, including the boat deck and boat deck house. Figure 49 is a section through the poop to above the poop deck. COURSE IN WOODEN BOAT AND SHIP BUILDING SHIP CONSTRUCTION 8» so COURSE IN WOODEN BOAT AND SHIP BUILDING SI < ■H > O < E Q c c c ■« Z; H a: ■fe O O < o r~ Tj4 -*< I t I I CR 00CV5 -H I I 00 Oi CO CO CO CO CO eo^- -* s^ i^ CO I I I I I I Oi .-H «5 "I lO ■* „; c~ lO ■* o t- ^ I I I 1 I ^ CO o »o o o a I I 1 I T □ OlO o— — ij c^ cocoeoco ' ' ' I I I T I I I I I I (CMco'Ss^cooicor-^Hoo J)I--.t^OcOOi-*- I I I I —< -M C±)C ■ '*'r--cof-.ei(N.r-.Qriix)-^<-ir-. I I I I I I I I I I I I I I I I r I iTi ijl I I III I iTl I eooor-ooooooocor— o-^iomeor^ I 1 I I I i I ] I I I I [ I I I I I I O Tji O O O C L I I I I I t I I I I iiooocooococococno — c-— 1 — CO .rt^^^^,^ncoeococococoeoco■I:^OcoOO«^co(^^ 1 I I I I I I I 1 I I I I I I I I I I I I ■-f■»fOOOOOOOOOOi±lOCOOlO■JC^^^OCOC^ CO r-i CM CS N CO -* — COCO 1 I I I OC- to 00 -— it-OlOCO-^-H-H^ — ^- I I I I I I [ I t I I 1 co5D-*eocococococococococo ot*^~o^~I>-^~eo I I 1 L I I I I 3-^eocococococococococo'*'-*a3ioOca»-(tD '■TlllIlfllllTllllIll iO-HOOOOOOOC3OOOO^i0M3^-f00 — C^ i-H (M iMM CO C- O O «o t~ (O >o o i:Ot--r~i-~iocococococococococot--iocMOr^05C^ - I I I I I I f I I I I I I I 1 I I I I I I --"■racMc^icMCQirOOOOC=iOOOOOOOOOOCM— Tfl-~-H to CO t-- o I I I I ■ I I I I I I I I I I I I I I I I I I I I I ■^CS'-i'-Hi-HOOOOOOOOOCMQOOf-rtlC^O ■^yaoooooooooooooo=0'*"coc--H -H c^ CS| CO iMin t— (N o -■ I I I I I I SOOOiM CCJCN - Sffq(M-^10«t-.OOCTi--CO-*iO«Or-COCC>00'-' — C^ l-H.-..— (.-l—IM-^^HIMCMNtMCil iMC^l N (M cq I M3J0S miij^ SHIP CONSTRUCTION 91 4 ■ CO W5 0> Oi en en 0> 0> 05 Oi OS O) Oi a> CO •— 1 ^H (6 ■ ■ ■lllllLllli'llllTVl '■ - T)H (O CO eo CO «0 «D CO iX) (O CO CD ea <0 CO -^ (M .-( ■ . 5-2-1 3- 5-0 2-4-6 1-5-1 d • O O 1— C^ C ^~ t^ O — C^CJiO ■ ■ 1 1 1 T ' '■ I-.-^CMi-i - ■ 00 i . , COCM t-~ -H - - tli-itl : : 1 r 1 1 ' • O0-JflCM ■ ^QOCOO» Oi»0 COi-i ■ ■ CD d Iz; • o^~oo CMO f^ t- t-r- 1^ CM cot^ t~ «* coo ■ - cDoooj^H oi io oo Tj— 1 tO'i'O 1 I 1 T ■ >0 O) CO CM ■ CO d Iz; ■ t^Tft— coc^or^r^c^p-t— tD-*iooocicot^ - 1 [ 1 1 1 1 1 1 1 1 1 { r 1 1 1 1 1 1 CM 00 to 00 CM OS OiO) Oi 01 Oi r* >* 00 •-< -O -H CO ,-( . ■ ! 1 1 1 I 1 1 1 1 1 1 t 1 1 1 1 1 1 1 t— COOO -H CO CO coco to CO COCOCOCM or^ — 00 CM ■ --.-HCMCMOlCMClCMCMCMCMCMCMCM^i-H ??t? - to ^- OlT- • ■ t-CMOC* O !z; - CO ^- to c- -* ■"*! -* -^ ^ f- CM CM Tt< lO -^ tj< 10 1-H ■ ■ 1 1 1 1 1 1 f 1 I T 1 1 1 f 1 I 1 1 1 ■ ■ -^-TfOO— iCMCOCOCOCOCOCOCOCOCM-HCTunc^lOOO ■ ■ 1-1 rt CM CM CM CM CM CM C<) CM CM COiOiOiO>r3COClCO-*'C-OCMCO-* ■ ■ ■ 1 1 1 1 1 1 I 1 1 1 1 1 1 1 I 1 1 1 1 1 COCOO-*COOOOOOO^CnioOCM»OI>->-'iO • * 1 1 T 1 1 1 1 1 1 ^ ( 1 1 1 1 1 1 1 1 1 00 -VOO ^ CM coco CO COeOCOCM MCM ^-0 t— lOCOQO - i-i^CMCMC-^CMCMCMCMCMCMCMCMCMCM— ■■-1'-' ■ ■ o d ■COCOiOC^COCOCMClCMiMCMCOOCOCOira^H^H — COO i rt CM — CO COr-OOOOOO 0000 t- lO CMf- Tl>CO-^ OCM CO ■ .OiiOCJl-!HCMCMCMCMC-lCMCMOlCMCM-HO00t^eD':t. 1 M3J3 ^"I'^X 92 COURSE IN WOODEN BOAT AND SHIP BUILDING oocc(M ■ ■ -oc^eo r— b~ CO ■ t^CM^ - iSiO CO ■ ( Knuckle 1 18- 2^6 17- 0-6 15- 9-0 14-0-5 9- 9-0 J,,j.li -lAA OMCOO OOOt- "^ -a a o^-c<^ fo ^r- Tt< ooooo Oio 0(Mcooct^r--t^t^t>.«3C^-^~t^^~^--^ — roc-, oomt— - J 1 1 1 f T 1 1 1 1 1 1 1 1 1 1 1 1 1 ■ O^OCM t— OC — • CM CM CM CM CM CM CM O t-~ CM r- CO « ■ 1-1 — -H CM CM CM CM CM CM CM CM CM « ^H eof-Oi-- 1 1 1 1 00 CO CO >— I 1 1 1 1 [>fO(N— 1 CO OCMOCMOOOOOOOO»Ot~»OiOu:i WO ■ C0C»"«<-H'J<0i0iOC>O<±)0CM— ■— " — CM-H« - 1-1 w CM CM CM (M CM CM CM CM w —■ CO o t— o 1 1 1 1 '! 0-*CO — O00f^t^t~t^t~-0-rf — O — CM 1 1 1 1 1 1 1 1 1 1 1 ( 1 1 1 1 1 1 00t~>*'C0OSiO-*^^^-*^00C0-^»O<©"5 icMir-cMiDcsoctoooocitic-qt^co— i — >W-HCMCMCMCMCMCM — -^1-" IP i : ; III eOi-" —1 ■ ■ ■ 1 - 1 • CMCO'tf'iOCDt^OOOiwirOTfi^COt-OOOsOO-H^-iCM.rS Q^ ^ ^^„„_„_^CMCMCMCMCM rt OOO-H — CM '— CM CM CM CM CM AS.3J0S aiA\ 1 SHIP CONSTRUCTION 93 to -■r Note:— Siding for Fir Figure 46. — Standard Wooden Steamship Wood20',fory. p. 16'. Moulded Lines — Body Plan. S6 CODRSE IN WOODEN BOAT AND SHIP BUILDING Figure 50 shows the section through the engine foundation, looking forward. One-third of the engine holding-down bolts are put through to the bottom of the foundation keelsons. The remain- ing two-thirds of the holding-down fastenings are heavy lag-screw bolts. Figure 51 is a section through the shaft tunnel, looking aft, and Figure 52 shows the section through the forecastle. SCANTLINGS The following are the scantlings, or dimensions, for various parts of the standard wooden steam- ship : Stem. — Sided 16", moulded 20", yellow pine. Apron. — Double 16x16", yellow pine. Knightheads. — Sided 20", moulded same as frame, yellow pine. Sternpost. — Sided 28" in way of shaft log, 16" at keel and head, moulded 24", white oak substitu- tion ; built up in four sections ; white oak inner stern post of yellow pine, of same dimensions as main post. Rudder Pos^.— Sided 16", moulded 18", white oak. Rudder Stock. — 18" diameter, best white oak. Rudder Blade. — Built up, yellow j^ine. Deadivood Knees. — 16" sided, hackmatac or oak. Horn Timbers. — White oak. Stern Framing. — Yellow pine. Forward Deadwoods. — 16"xl8" yellow pine. SHIP CONSTRUCTION 9T After Deadwoods. — 16"xl8" yellow pine. Shaft Log. — 14"xl4", in four pieces, white oak. Hull Bulkhead Planking. — 3"x8" double diag- onal, yellow pine. Hull Bulkhead Studding. — 8"xl2" yellow pine. Pointers. — 3"xl2" yellow pine. LOFTING THE SHIP The lines are laid down on the mould loft floor full size, as previously described. See FigTire 53. If space will not permit the laying down of the full length, it can be laid down in two or three sections, one overlapping the other. The sections must be long, however, so that the lines may be properly faired up. All sections are laid down and the lines proved before getting out the moulds. It is not an easy task to properly fair in these lines, for while look- ing at one portion of the ship, it is impossible to see the other end; yet much depends upon the accuracy of the mould loft^man in getting out his moulds, in order to conserve the labor of the car- penter in dubbing off and fairing up the scantlings while in frame. Moulds. — The moulds are prepared by the mould loftsman, having plainly marked on them the various beveling stations, water lines, and other means of identification, for ready reference when assembling. All have to be plainly numbered and show the number of pieces required. These are 98 COURSE IN WOODEN BOAT AND SHIP BUILDING Figure 47. — Midship Section of SHIP CONSTKUCTION .^c o r T'f ° ;:,'';a -? Standard Wooden Steamship. 100 COURSE IN WOODEN BOAT AND SHIP BUILDING given to the mill superintendent, and from them he lays out his parts. — ftOAT DEC Figure 48. — Section from Bridge Deck to Top of Wheelhouse of Standard Wooden Steamship. FRAMES The frames are double saAved, spaced 36" center to center, separated at the butts with 2-inch chocks, and each butt fastened with II/4" treenail. The frames are laid out from the moulds, as SHIP CONSTRUCTION 101 5YR PUANKIMO Figure 49. — Section Ttiroiigh Poop. 102 COURSE IN WOODEN BOAT AND SHIP BUILDING -soLiD Yp. riooKs rirrcp ;n »*ay cr engine: bed pLate CAuLKCD OR WEDGE.D TWSHT C^^tiKC riTTJNG ENGINE rouhOATION KCEL S^^ BASE — ■STAg&ftARD Figure 50. — Section Through Engine Foundation, Looking Forward. f mii vJ^ftHf lutJeiWJfe^fl. n»M-^t.LCl. . ^ _Ciflr,a &V IQ' YP-SJPE Pt-ANKING Figure 51. — Section lluough Shaft Tunnel, Looking Aft. SHIP CONSTRUCTION 103 # BeAMS SPAcep [ FbcstixPcck _ I yUPPER C'ECK ^ p-l-AMKll-iS Figure 52. — Section Through the Forecastle. 104 CODKSE IN WOODEN BOAT AND SHIP BUILDING SHIP CONSTRUCTION 105 a +-» O hi I a a 106 COURSE IN WOODEN BOAT AND SHIP BUILDING shown in Figure 54, and cut to the required bevel on the band saw. See Figures 55 and 56. The gauge on the side of the machine registers the angle at which the saw is cutting. The man guiding the stock through the saw Figure G5. — Beveling Frames on tlie Band Saw. announces the various degrees or bevels as he nears the mark on the timber, while the operator at the Avheel gradually tilts the saw one way or the other, as the case may be, fairing one bevel into the other as the degrees change. Mill Floor Carriages. — In the well-equipped plant the mill floor is made up of sectional car- SHIP CONSTRUCTION 107 Tiages, as shown in Figure 57. On the top of the carriages are a series of rolls. The tops of the rolls are level with the working table of the machines, so that a heavy timber can ■ W^S^^^^^^^ 1 1 1 ^H ^^^B^M^ 0^^^S^ •i '. I ^^1 I^^^J^H^^^ HtJ- ^^^^^k II ^^^^KSk^^H B ^^ 1 ■ ■ H in s ^^B ^^^^^^^^^^^1 iP^^v- - "^^'^^^B K ^^^H ^HH t;^i'-'' "" - fl ^^^HH B^^S^^ ■"■ - ,^^1 ^^^^^^^s '. ■ _ - '^I^^H t;^^^ ^^^H^^^^R ».-■?- " ^ '- ' ' "^"BSH ^^^3 ■BHr!^ ^SasL^ "" ■ ; .-*^S ^M Figure 56. — Cutting a Straight Timber on the Band Saw. be iDassed through a machine and moved about with but very little exertion on the part of workmen. The timbers are then put on trucks and distributed to the assembling platforms at the nead of each "way." See FigTire 58. Ways. — The set of heavy timber sills upon which 108 COURSE IN WOODEN BOAT AND SHIP BUILDING a ship is built, and upon which the vessel slides in launching, is called a way. Launching ways sup- . . . ;<*»ii. ■'';^;i::-ii '^.ii.«i*K?5S- -^'.fy--'"- ■■-.'.< -•- ■ * ^ ;* _ , .. : ^^j^mm^^^:^"'''. ^ ^''^ M'M^ \ itk i^sitt,''-- '"^^iBlBj ^^SHtflMr . -- r .^HBtefiBigS'^^^a.^-^'' '. . '•*' ■'?^; ' ! ^^^jfe^'^^r^ftr^j^i^ ■• 9H£^^^iiS^^^£i^A^^^ud^4K^^:ifj'?HUu.^' -^-vj' ■■j^KlS Figure 07. — Sectional Carriages In Mill for Handling Heavy Timbers. port the cradle of a ship, and form the track on which it descends into the water. See Figures 99, 100. SHIP CONSTRUCTION 109 CHAPTER VI MACHINES AND LABOR-SAVING DEVICES Sawing and Handling Large Timbers. — Special machines and labor-saving devices have been de- signed to partially offset the shortage of labor. Figure 59 shows the method of sawing a heavy timber in a large modern mill. The first slab has been removed and the second cut is being made. The timber rests on a carriage Avhich slides back and forth, and is controlled and held in position by a series of hooks operated by a lever on the carriage. The finished timbers are moved about in the yard on trucks, as shown in Figure 60. Bevel and Edging Machines. — One of the latest machines to be designed is a bevel and edging machine used for beveling ceiling and planking (including calking seams), and forecastle deck beams ; also for faying knees, rounding edging of waterways, main rails, pin rails, etc. In Figure 61 is shown a timber starting through the machine at an angle of 11 degrees to the right, and in Figure 62 the other end is shown coming out of cut at an angle of 11 degrees to the left, the angle continually changing as the work was done. The finished timber as it left the machine is shown in Figure 63. 110 MACHINES AND LABOR-SAVING DEVICES 111 112 COUESE IN WOODEN BOAT AND SHIP BUILDING MACHINES AND LABOR-SAVING DEVICES 113 In beveling ceiling planking, a complete strake can be laid out at a time ; battens are nailed on each timber, and the timbers placed on roller skids alongside of the machine, from which they can quickly and easily be placed on the carriage and run through. The collar of the machine rests against the batten, and this regulates the depth of the cut and the shape. Surfacing Knees. — The method of surfacing knees is shown in Figure 64. Eleven knees are shown after having been surfaced two sides. These eleven knees were loaded on the carriage, surfaced one side, turned over and surfaced on the other side, the complete operation requiring only fifteen minutes. "Faying" the knees is a simple operation, as shown in Figure 65. A small platform is placed on the carriage, and a batten is nailed on the khees in the same manner that is used in working ceiling and planking. To illustrate the work accomplished the carriage was reversed and the machine stopped. Working Rudder Stock. — The working of the rudder stock shows another possibility of this machine. Formerly all the work was performed by hand, while the surfacing of the various parts is now done on the machine. In Figure 66 the rudder stock (iron bark) is placed on blocks sawed to hold it at 45 degrees, the carriage of the machine is run forward, and the cutting done on the top beveling head. 114 COURSE IN WOODEN BOAT AND SHIP BUILDING Figure 61.— Starting a Cut at an Angle of 11 Degrees to the Riglit. MACHINES AND LABOR-SAVING DEVICES 115 Figure 62. — Finishing the Cut at an Angle of 11 Degrees to the Left. 116 COURSE IN WOODEN BOAT AND SHIP BUILDING Figure 63. — The Finished Timber. MACHINES AND LABOR-SAVING DEVICES 117 s 118 COURSE IN WOODEN BOAT AND SHIP BUILDING As it is especially hard wood, comparatively light cuts are made, and each time the carriage is reversed the beveling head is lowered slightly by power (the dial indicator showing the exact posi- Figure 65. — Faying Knees on a Special Beveling Machine. tion) and another cut is taken. This operation is continued until the timber is cut to the desired depth. The rudder stock is then placed in such a position that another corner can be cut do%vn in the same manner. MACHINES AND LABOR-SAVING DEVICES 119 120 COURSE IN WOODEN BOAT AND SHIP BUILDING MACHINES AND LABOR-SAVING DEVICES 121 3 o5' 122 COURSE IX WOODEN BOAT AND SHIP BUILDING MACHINES AND LABOR-SAVING DEVICES 123 Figure 67 shows the same piece after sixteen cuts have been completed, the lower part beveled two ways, and the sides surfaced. It leaves the machine as shown in Figure 68, practically fin- ished, requiring comparatively little time with Figure 70.- -Eecord Keel Laid in Ten Minutes in the Atlantic Coast. Prominent Yard on hand tools to complete the work as shown in the illustration. Every piece of ceiling used in the ship shown in Figure 69 was beveled on this machine, no hand tools being used. Even the back of the ceiling at the turn of the bilge was beveled, using the top beveling head of the machine, thus showing the amount of hand labor that may be saved. Setting Up the Keel. — The keel. Figure 70, is made of yellow pine, 16 by 14 inches, in lengths of 124 COURSE IN WOODEN BOAT AND SHIP BUILDING MACHINES AND LABOR-SAVING DEVICES 125 about 40 feet, scarfed together with 7-foot scarfs. Each scarf is fastened with eight li/4" bolts set up over clinch rings at both ends. The keel is set up on the keel blocks, wedged and shored in position. The keel shown in Figure 70 probably holds the Figure 72. — Assembling Platform, Shoving 1' i^-onals. record, having been laid in 10 minutes in an Atlantic Coast shipyard. Assembling Platform. — At the head of each way is an assembling platform as shown in Figure 71. Timbers are fastened to the platform on the diagonal lines, and upon these timbers the frames are assembled as in Figure 72. Fitting and Fastening Frames. — If the diagonal lines and other reference lines have previously been transferred from the moulds to the frame timbers before sawing, they will readily find their 126 COURSE IN WOODEN BOAT AA'D SHIP BUILDING proper location. The timbers come already shaped from the band saw, so that very little hand work is required at this stage of construction. After the joints are fitted, the frames are fas- tened together with %-inch drift bolts and I14" treenails. The holes are bored with an automatic auger bit, followed up by a man putting in the tree- nails as fast as the holes are bored, and again fol- lowed up by two men driving in the treenails, so that by the time the last hole is bored the frames are practically ready to raise. CHAPTER VII BAISING THE FEAMES As soon as the carpenters finish a frame, the riggers take charge in raising it into position. In li^igure 73 is shown a frame about to be raised. Two tracks are placed on either side of the ways, running from the assembling platform the entire length of the ways, and on these tracks the frames are run to their positions. Chocks are placed against the previous frame raised, to give the proper spacing of the frames and serve as a stop as the frame slides down the ways. Figure 74 is a nearer view of the frames in posi- tion ready to raise, and in Figure 75 a frame is being raised. As soon as the frame leaves the platform, the next frame is begun, and in that way both riggers and carpenters are kept busy. While one assem- bles, the other group raises. Figure 76 is a near view of the frames in posi- tion. Figure 77 shows the same ship a short time before, the ways having been lowered while the ship was on them, as shown in Figure 76. CANT FRAMES The cant frames are the half frames at the fore and aft of a ship. It is usual to dispose the trans- 127 128 COURSE IN WOODEN BOAT AND SHIP BUILDING verse framing of a ship entirely in planes per- pendicular to the trace of the load water line, with the longitudinal plane of synunetry of ships. This practice leads to a large and varying bevel heing given to the frames at the ends of a ship with a very bluff bow or stera, and it becomes a prac- Flgure 73. — The Frames Are Run on Two Tracks, One on Either Side of the Ways. tical question whether it would not be better at such parts to dispose the frames in planes Avhich are more nearly normal to the general surface of the ship, and which need not be perpendicular to either of the three planes of reference. It is of great economical value and highly im- portant that the timber frames be all square or nearly square sections, thus eliminating great bevels. Most of the bevels in wooden ship timbers RAISING THE FRAMES 129 do not exceed 10 degrees, very few exceeding 15 degrees. Bolting the Frames. — The lower ends of the cant frames are let into the deadwood 1 inch and bolted with six bolts in each half — four ll^" and two IVs". At least two of the ll^" bolts extend through Figure 74. — Frames in Position Ready to Raise. the half frame, through the deadwood, and set up over clinch rings. The cant frames are built up in a similar manner to the main frames. Figures 78 and 79 show the heels of the cant frames fore and aft of the same ship. In FigTire 79 the flooring is being laid and the illustration shoAvs the long treenails in posi- tion ready to be driven in. A number are set up at one time and then the operation of driving thein 130 COURSE IN WOODEN BOAT AND SHIP BUILDING RAISING THE FRAMES 131 Figure 76. — Frames in Position. Figure 77. — These Ways Were Lowered While the Ship Was in Frame. 132 COURSE IN WOODEN BOAT AND SHIP BUILDING is performed dt one time. Figures 80 and 81 show the heads of the same frames. Keelsons. — The keelson timbers are eight in number, as shown on the midship section, Figure 47. These are put in in lengths not less than 48 Pigure 78. — Cant Frames Looking Forward, Showing Heels oj Timbers. feet long, connected Avith 7-foot scarfs, care being taken to get the best shift of scarfs possible. Figures 82 and 83 show the keelsons being in- stalled. At the lower left-hand corner of Figure 83 an opening is seen in the frame work. This opening is made after the frames are in position, and leads to a chute through which the heavy timbers of the keelson are hauled into position. Fairing-up Worh. — The framed body of the ship should be properly ribbanded and shored to RAISING THE FRAMES 13S Figure 79. — Cant Frames Looking Aft, Sliowing Heels of Timbers. Figure 80. — Looliing Forward — Heads o£ Timbers. 134 COURSE IN WOODEN BOAT AND SHIP BUILDING retain shape. The inside surface of the forms should be dubbed with an adze, so as not to leave over 10 per cent of the sawed surface on the frames. The outside of the frames should be dubbed for each strake of planking, and the outer surface of planking rounded to conform to the shape of the Figure 81. — Looking Aft — Heads of Timbers. ship. The thick ceiling is rounded on the back, so as to fit the frames. Iron Strapping. — The entire frame work is braced and reinforced by a system of iron strap- ping. A top belt of %" by 8-inch iron extends from about 12 feet from the forward end to about 12 feet from the aft end of the ship, fastened to each frame bv 1-inch by 10-inch countersunk bolts staff- gered. Diagonal straps of i/.-inch by 4r-inch iron RAISING THE FRAMES 135 136 COURSE IN WOODEN BOAT AND SHIP BUILDING a 5 RAISING THE FRAMES 13T are let into the outside of the frames and inclined at an angle of 45 degrees each way. The diagonals are connected to the top belt by two %-iiicli rivets and at each crossing by one 1-inch rivet, and also fastened to each frame timber by one 1-inch countersunk bolt. They should be carried well down and wrapped around the bilge far enough to overlap the ends of the floor timbers. The iron straps should be painted with two coats; of red lead and oil before planking. CHAPTER VIII PLANKING AND FINISHING Layout of the Ship.—Beiore going into the de- tails of planking it will be well to refer to the Figure 84. — Bow of Ship Ready for Planking. illustrations to get the general layout of the ship before planking and in the finished state. 138 PLANKING AND FINISHING 139 Figure 84 shows the bow of a ship ready for. planking. Figure 85 shows the same bow planked, with the staging still in position. Figure 86 is a closer view of the details of the bow construction. !_ >f";ai^ R". iMBE^ilBnflKftQutf 5^-i^i#^ -*— M ^^M 9" ■ Figure 85. — Bow of Ship Planked, Showing Staging. Preparations for Planking. — Figure 87 shows the starboard side of the ship ready to plank. Note the escaping steam, showing the location of the steam box used in bending the planking. Figure 88 shows the ship partially planked. In Figure 140 COURSE IN WOODEN BOAT AND SHIP BUILDING 89 it is completely planked just before launching, and in Figure 90 the finished ship is seen after launching. Material. — The planking and ceiling throughout is made of yellow pine lumber. The ceiling is put Figure 86. — Close-up View of Ship, Showing Detail of Bow Construction. in in lengths 30 to 50 feet long, and the planking in lengths 24 to 40 feet, averaging 32 feet long. The bottom planking is 5 inches thick and 14 inches wide, bilge planking 6 inches by 10 inches, the planks narrowing as they reach up the side of the PLANKING AND FINISHING 141 142 COURSE IN WOODEN BOAT AND SHIP BUILDING I PLANKING AND FINISHING 143- 04 I 144 COURSE IN WOODEN BOAT AND SHIP BUILDING ship, beginning with 5-inch by 10-inch, then 5-incH by 9-inch, and 5-inch by 8-inch, the topside plank- ing being 6-inch by 9-inch. The lengths of the planking are jointed with square butts on the frames, with the seams out- gauged for calking. The circle of the stern between the knuckle line and poop deck is planked vertical, as shown in Figure 91. Figure 92 shows the interior construction of a standard wooden steamship, looking aft. Figure 93 gives a close-up view of a framing platform. Steam Box. — The steam box for bending the ceil- ing planks is located inside the ship, while the boxes for bending the outside planking are located at the head of the ship or the most convenient place possible. The steam boxes are made in lengths about 8 feet long and about 30 inches square inside the box. A number of these lengths are bolted together to get any length of steam box desired. The timbers are cut to the required shape before steaming them. All joined surfaces throughout the construction of the hull should be treated with a wood preservative before installing. Clamps and Wedges. — When ready to install, one end is fastened and held in position by a clamp, and as the plank is bent in position, a hook is fas- tened around the frames at intervals and a short timber is placed between the hook and the outside of the planking. Wedges can then be driven to PLANKING AND FINISHING 145 146 COURSE IN WOODEN UOAT AND SHIP BUILDING bring the planking up tight against the frames. These hold it in position until fastened, when the wedges are removed. The garboard strake is fastened to each frame Figure 91. — Stern of Ship, Showing Vertical Planking. with four 1-inch bolts 18 inches long, and edge bolted to the keel with 1" by 36-inch bolts every second frame spacing. PLANKING AND FINISHING 147 t'Vir t^r-^ 148 COURSE IN WOODEN BOAT AND SHIP BUILDING Bottom, Bilge, and Side Planking. — The bottom, Tjilge, and side planking is fastened with %-incli Lolts driven over clinch rings. These rings should Figure 93. — View of Framing Platform. he countersunk and the holes plugged, with the grain of the wood running in the same direction as the grain of the wood in the planking. In addition to the bolts the wide planks have PLANKING AND FINISHING 149 four treenails in each frame and the narrow planks two treenails, all driven in full length, wedged on outside of planking and inside of ceiling with oak wedges. Figure 94. — Ready to Launch. The wedges are placed across the grain of the wood through which they are driven. The holes for the treenails are bored with long, power, ship auger bits. The head of each treenail is protected with an 150 COURSE IN WOODEN DOAT AND SHIP BUILDING Fij;:nre DT). — Framing the I'oop Deck. Figure 96. — Poop Deck Completed. PLANKING AND FINISHING 151 i£ti>l a^**' Figure 97. — Raising tlie Rudder. Figure 98. — Shaping the Masts. 152 COURSE IN WOODEN BOAT AND SHIP BUILDING PLANKING AND FINISHING 15S 134 COURSE IN WOODEN BOAT AND SHIP BUILDING iron cap to take the blow of the sledge while being driven in, to prevent it from splitting. After the planking is fastened, the outer sur- face is rounded to conform to the shape of the vessel and joined so as to properly take the paint. Calking. — The seams in the hull are opened up with a dumb-iron where it is necessary to enlarge them to make room for the oakum. Beginning with the garboard, which should be calked with at least eight threads of oakum, the number of threads is reduced up to the five-inch planking, which should be calked with at least four threads of oakum, double horsed. The oakum is kept in the store room as it comes in bales, and is spun into threads for the calkers. Cementing Seams and Painting. — The outside planking seams up to the 18-foot water line should be filled with cement, and the remainder of the outside seams painted with a white-lead paint and linseed oil. The bottom of the vessel is painted with three coats of cojoper paint up to the light water line, and above the light water line a priming coat and two coats of pure lead and linseed oil. As soon as the hull is completed the vessel can be launched, thus releasing the ways for the laying of another keel. The hull is then turned over to the shipfitters to complete. Fignire 94 shows the hull of the vessel just before launching. Ship fitting. — Most of the difficult technical prob- lems arising in ship work are found in the con^ PLANKING AND FINISHING 1S5 156 CUURSE IN WOODEN BOAT AND SHIP BUILDING h o WIRELESS HOUSe- OOINER DECK COVERED WITH CANVAS r :0»L CHUTE WOOD 1-AOgy MATCHCOVERS) h4 V.I •11. |«>!|p'= Figure 102. — Wheel House and Navigating Bridge PLANKING AND FINISHING 157 struction of the hull. When the shipfitters take charge, as is shown in Figure 95, framing the poop deck, the work takes on the nature of house con- struction, with the ordinary problems that may confront the average carpenter. Fignire 96 shows the poop deck completed. Raising the Rudder. — The methods employed in getting out the rudder stock have been shown in Figures 66, 67, and 68. Figure 97 shows the method of raising the rudder in position. 7/V Figure 103. — Top of Wheel House. Shaping the Masts. — Each ship (standard car- rier) is fitted up with two wooden pole masts, fitted with cargo booms. Fignire 98 shows the shaping of the masts. These masts were completely shaped by hand, the rough cuts being made with an adze and finished with a hand plane. Shipyards and Ways. — Figures 99 and 100 give a panoramic view, taken June 12, 1918, of a prom- inent shipyard on the Atlantic Coast. Five ships are seen in course of construction and five ways are shown to the left of Fignire 100, which is a continuation to the left of the view in Figure 99. 158 COURSE IN WOODEN BOAT AND SHIP BUILDINe Figure 104. — Boat Deck, Standard Wood Steamship. PLANKING AND FINISHING IS* Figure 105. — Top of Gun House. Figure 106. — Poop Dofk. 160 COURSE IN WOODEN BOAT AND SHIP BUILDING Figure 107. — Bridge Decli, Standard Wood Steamsliip, PLANKING AND FINISHING 161 This makes a total capacity for ten ships. In the distance is seen the fitting-up wharf, showing a ship with the painted camouflage effect, or protec- tive coloring adopted for use in wartime. STANDAED WOOD STEAMSHIP Plans and sections of the standard wood steam- ship built for the United States Shipping Board, Figure 108. — Forecastle Deck. Emergency Fleet Corporation, are shown in Fig- ures 101 to 111 inclusive. An inboard profile of the ship is seen in Figure 101, and the arrange- ment of the decks and numerous other details appear in the remaining illustrations. Figure 102 shows details of the wheel house and navi- 162 COURSE IN WOODEN BOAT AND SHIP BUILDING m. i iuv//,riii.inmii ; Figure 109. — Section Through Engine Room, Loolsing Forward. PLANKING A\D FINISHING 163 Figure 110. — Section Througli Boiler Room, Looking Aft. 164 COURSE IN WOODEN BOAT AND SHIP BUILDING gating bridge, and Figure 103 the top of the wheel house. The layout of the boat deck is seen in Fig. 104, and the top of the gun house in Figure 105. Figure 106 shows the poop-deck arrangement, and Fig-ure 107 the bridge deck. The forecastle Figure 111. — Plan View at Dynamo Flat ani.1 Engineer's Store Room. deck plan appears in Figure 108. Figure 109 shows a section through the engine room, looking forward, and Figure 110 a section through the boiler room, looking aft. Figure 111 is a plan view at the dynamo flat and the engineer's store- room. CHAPTER IX HAND TOOLS Among the special hand tools used in wooden boat and ship building, the most important are the adze, the broadaxe, calking irons, the calking mallet, and ship auger bits. A description of each of these and their respective uses is given below. A complete list of the hand tools used by the ship carpenter and boat builder is as follows : Adze — lipped Chisels — Axe — plain broad Cape cold Bevel — ship carpenter's slice, 21/2" Bits wood, 1/4" to 2' extension Dividers screwdriver (large Draw knife and small) ship auger with spur Gauges — 1^" to 1" marking wood, 1^" to 2" Brace — ratchet Hammers — Burr set ball pein Calking irons claw Calking mallet Oilstone 165 166 COURSE IN WOODEN BOAT AND SHIP BUILDING Reamers — wood, I/2' 11/2" Saws — Pincli bar, 20" Planes — bailer, for hollowing plank bilge, for smoothing side of hull compass fore jack rabbet smoothing Pliers — end cutting Plumb bob Easp — wood to compass cross cut hack, panel rip Spirit level Spoke shave Squares — large steel small try square, 7V2' Adze. — Figures 112, 113. The adze is a tool resembling a hoe and is used in much the same manner for shaping large parts where the wood to be removed is too much for the chisel or the plane. The lipped adze has the extreme ends of the blade turned up and is by far the best kind, as these lips insure a clean cut and prevent raising splinters. For the best results the cutting should be across the grain. See Figure 114. For converting large material when machinery is not available, the roughing is done with a broad axe ; the adze is next used to get close to the finish dimensions, and then the work is smoothed up with a plane. Broad ^a;e.— Figure 115. This axe differs con- HAND TOOLS 167 Figure 112. — Plain Adze. Figure 113. — Lipped Adze. Figure 114. — Scarfiog Timber witli an Adze. 168 COURSE IN WOODEN BOAT AND SHIP BUILDING Figure 118. — Calkicg Mallet. Figure 119. — Ship Auger Bits. HAND TOOLS 169 siderably from the ordinary axe used for chopping. The blade is wide and is sharpened by beveling- one side more than the other, somewhat like a chisel. Both blade and handle are offset, the whole form and hang being adapted to hewing on the side of large pieces of timber. Calking Irons. — These are made of steel in various shapes and sizes. The two in general use are the dumb-iron (Fig-ure 116), which has a tapered blade almost sharp, and the making-iron (Figure 117), which has a small blunt end with a channel in it, used for going over the cotton in the seams after it has been driven in by the driving- iron. The dumb-iron is employed to open the seams that are too tight. Calking Mallet. — Figure 118. This is a tool used in connection with calking irons for driving cotton or oakum into the seams, to make them watertight. The head, which is long and small in diameter, is usually made of live oak and fitted with iron rings to add weight and prevent splitting. Several sizes are made, the smallest being suitable for boat work. Ship Auger Bits. — Figure 119. These are used for boring long holes. They are of different shapes and are made with and without the feed screw, or spur. Those without the spur, sometimes called "barefooted," are preferred for very long holes, as they are not so readily deflected from a straight course. The commercial bits are often too short, but it is a small job for a blacksmith to weld in a piece, making any length required. CHAPTER X WOODEN BOAT AND SHIP TERMINOLOGY After-timbers. — The timbers abaft the midship section of a vessel. Air-port. — An opening in a ship's side for air, closable by a shutter, sidelight, or deadlight. Apostle. — A knighthead or bollard-timber on a deck, for belaying hawsers and heavy ropes. Apron. — An upper member of the stem on the inboard side of a boat. Arch-hoard. — The part of the stern over the counter, under the knuckles of the stern timbers. Auger-bit. — A boring-bit with a twisted shank, which clears the chips out of the hole. Balance-frames. — Those frames of a ship which are of equal area and equally distant from the ship's center of gravity. Balcony. — The stern gallery of a ship. Batten. — A thin strip of wood used in fairing lines. Beak. — The part of a ship forward of the fore- castle, fastened to the stem and supported by the main knee. Beam. — One of the curved transverse timbers ■of a vessel, supporting a deck. Beam-line. — The line indicating the intersection of the top of the beams with the frame. 17(1 SHIP BUILDING TERMINOLOGY 171 Bearding-line. — The line made by the curved surface of a ship's skin with the stem, keel and stern-post. Bend. — One of the strong planks on a vessel's sides to which the beams, knees, and futtocks are bolted. . Bending-strakes. — Two strakes worked near the coverings of the deck, running fore and aft a lit- tle thicker than the rest of the deck, and let down between the beams and ledges so that the upper side is even with the 'rest. Bevel. — Any angle in a timber except one of 90 degrees. Beveling. — The angles which the sides and edges of each piece of a frame make with each other. Beveling-edge. — The edge of a ship's frame which is in contact with the skin. Bilge. — The flat portion of a ship's bottom, or the point at which the frames turn from the bottom to the sides. Bilge-planks.— Strengthenmg planks of the in- ner or outer skin, at the bilge. Bilge-ivay. — The foundation of the cradle sup- porting a ship upon the sliding-ways during build- ing and launching. Binding-strakes. — Thick strakes, planking, or wales, at points where they may be bolted to knees, shelf-pieces, etc. Body-plan. — An end elevation of a hull, showing the water lines, buttock and bow lines, diagonal lines, etc. 172 COURSE IN WOODEN BOAT AND SHIP BUILDING BoU-strake. — The strake or wale through which the beam fastenings pass. Bow-lines. — Curves representing vertical sec- tions of the bow end of a ship. Break. — An abrupt change of level, as of a deck. The break of a poop-deck is where it ends forward. Bridge. — A partial deck running from side to side of a vessel amidship. Building-block. — One of the temporary struc- tures resting upon a slip and supporting the keel of a ship while building. They consist of blocks of timber so arranged as to be removable by knock- ing out the key-pieces or wedges. Building -slip. — A yard prepared for shipbuild- ing. It includes one or more slips, or inclined planes on which a vessel in its cradle is supported while on the stocks in the process of construction, or upon which a ship is hauled for repair. Bulge. — The flat portion of a ship 's bottom ; the bilge. Bulkhead. — A partition in a ship which divides the interior space into compartments, which may be made watertight. The bulkheads affording the greatest protection are those placed a few feet from the stem and stern respectively, the forward one checking the inflow of water through a dam- aged stem, and the after one averting the danger of any accident that might arise to the sternpost or rudder-braces, or to the tube of the shaft of screw-vessels. The water taken into these com- partments would only slightly impede the way of SHIP BUILDING TERMINOLOGY 173 the ship by throwing her out of trim, as the quan- tity would be comparatively small. The bulkheads more amidships assist in strengthening the ves- sel, and serve to prevent fire from spreading be- yond the compartment in which it started. In case of a leak they confine the water to the com- partment which it enters. Watertight bulkheads have been used for ages in Chinese shipbuilding, but in this country are more generally employed in iron than in wooden vessels. In small vessels they can only be used transversely, but in larger ones they may be applied longitudinally as well. Butt. — The meeting joint of two planks in a strake. Tlie joint between two strakes is a seam. Buttock. — The rounded-in, overhanging part on each side of a ship's stern in front of the rudder. It terminates below by merging into the run. Buttock-lines. — The curves shown by a vertical longitudinal section of the after part of a ship's hull, parallel to the keel. A similar section for- ward shows the bow-lines, and a continuous sec- tion through the whole length of the ship exhibits the buttock and bow lines. Calking. — The process of filling the seams be- tween the planks of vessels, and of spreading the ends of the treenails, by driving in cotton or oakum, to make the seams watertight. Oakum is made by cutting old ropes and cables into short lengths called junk and picking that to pieces. The seam is opened with a dumb-iron or deck-iron, driven with a calking mallet, and the threads of oakum driven 174 COURSE IN WOODEN BOAT AND SHIP BUILDING in, one after another, with a calking iron or making iron. It is then payed with melted pitch. Camber. — A curvature upward, like the rise or crown of a deck amidships, or of a bridge or a beam; the curve of a ship's plank. This shape is given to increase stability. Cant. — An angle, bevel, or slope. Cant-frames. — Bow and stern frames canted from vertical position for the purpose of eliminat- ing greater bevels. Cant-timber. — A ship timber that is not square with the keel, or that makes an angle with the keel of less than 90 degrees. Cat-beam. — The longest beam in a ship; the beak-head beam. Ceiling. — That portion of the inside skin of a vessel between the deck-beams and the limber- strakes on each side of the keelson. It is also called the foot-waling. The strakes of the ceiling immediately below the shelf -pieces which support the deck-beams are called clamps. The outside planking is called the skin. Center-line {C.L.). — The central, longitudinal, vertical section of a vessel's hull. Chain-plate. — One of the plates of iron bolted below the channels, for the attachment of the dead- eyes to which the shrouds and backstays are se- cured. Channel. — A corruption of chain-wale. A flat ledge of wood or iron projecting outward from SHIP BUILDING TERMINOLOGY 175 the ship's side, for spreading the shrouds or stand- ing rigging at each side of the masts, and protect- ing tlie chain-plates. The channels are at the level of the deck beams. Chock. — 1. A block, usually wedge - shaped, driven behind the props of a cradle to prevent it from slipping on the ways before the ship is ready to launch. 2. A piece of timber, framed into the heads and heels of a ship's timbers at their junctions, to act as a lap to the joint and make up the deficiency at the inner angle, as in the stem-piece and the main piece of the head ; also in the deadwood, etc. Clinker-built. — A term applied to boats in which the lower edge of each plank overlaps the one next below it, like the weather-boarding of a house, or the shingles or slates of a roof. In such boats the lower edge of each strake of plank overlaps the upper edge of the next strake below. They are not built upon frames, but upon temporary trans- verse sectional moulds, two, three, or four in num- ber, which are fixed at their proper stations on the keel. The strakes are then put on, beginning with the garboard strake, and bent to the fig-ure given by the moulds. Each strake is fastened to the "next below it by nails, driven from the outside through the laps or lands, or by screws. When two or more lengths of plank are used in a strake, they are scarfed to each other, the outside lap of each scarf pointing aft. Coal-bunker. — One of the spaces provided in a 17U COURSE IN WOODEN BOAT AND SHIP BUILDING ship, convenient to the furnace-room, for keeping the fuel. Coamings. — Also spelled combings. The raised border or frame of a hatchway, to prevent the water on deck from flowing below. The fore and aft pieces of a hatchway frame are coamings, those athwart ship are head-ledges. The former rest on carlings, which extend from beam to beam, and the latter rest on the deck beams. Companion. — A wooden covering over the stair- way to a ship's cabin; a companion-hatch. The staircase is the companion-ladder, or companion- way. Counter. — That part of a ship's stern which hangs over the stern-post. The counter-timbers spring from the wing-transom, which extends across between the fashion-pieces, crossing in front of the stern-post, near its head. At the top of the counter-timbers is the taffrail. Cradle. — The frame in which a ship lies on the ways, and which accompanies her into the water in launching, separating from the ship by the act of floating. In its simplest form, the cradle con- sists of three longitudinal timbers, united by ribs or crosspieces. It is also used in hauling out a ship for repairs. Cross-heam. — A beam in a frame laid cross- wise. Cross-spalls. — Cross timbers uniting the heads of two futtocks. SHIP BUILDING TERMINOLOGY 177 Cutwater. — The forward edge of the stem or bow of a vessel ; that which divides the water right and left. It is fayed to the forepart of the stem. Deadnwod. — The lower member of the stem or stern on the inboard side of a boat ; also the solid mass of built-up timbers at the narrow portions of the extremities of a ship's frame, fore and aft, above the keel, and continued as high as the cutting-down line. In vessels designed for service in arctic waters, the deadwood is in unusual quan- tity, to give solidity to a structure liable to contact with ice-floes and drifts. Dead'ivorks. — -The parts of a vessel above the load water line. Deck. — Any floor in a ship above the bottom of the hold. Decks may run from stem to stern, or be only partial. In three-decked ships the decks above the water-line are known as the upper, main, and lower decks. The deck next below the water- line is known as the orlop deck. The upper may be known as the spar deck, with the forecastle as its foremost part and the quarter deck aft. The waist is the space amidships. A transverse deck extending across the middle of the vessel is called either a hurricane-deck, a bridge-deck, or the bridge. Detached structures on a deck are called deck-houses. Deck-transom. — A horizontal timber under a ship's counter. Diagonal. — 1. A timber brace, knee, plank, truss, etc., crossing a vessel's timbers transversely. 178 COURSE IN WOODEN BOAT AND SHIP BUILDING 2. A line cutting the body plan diagonally from the timbers to the center line. 3. An oblique brace or stay connecting the hori- zontal and vertical members of a truss or frame. Diagonal-built. — A term applied to boats in which the outer skin consists of two layers of planking making angles of about 45 degrees with the keel in opposite directions. Such boats are built, like clinker-built boats, upon temporary transverse moulds. After setting up and fixing the moulds upon the keel, the gunwale, a shelf -piece, and a series of ribbands are temporarily fixed in the moulds. Two layers of planking are then put on, bent to fit the moulds and ribbands, and fas- tened to each other and to the keel, stem, stern- post, shelf, and gunwale with screws or nails, driven from the outside, and clinched inside upon small rings, called clinch-rings or roves. The gun- wale is then shored, to keep it in shape. The moulds and ribbands are taken out, and floors, thwarts, etc., are put in as in a clinker-built boat. Diagonal-lines. — Lines showing the boundaries of various parts, formed by sections Avhich are oblique to the vertical longitudinal plane, and which intersect that plane in straight lines parallel to the keel. Displacement. — The weight of water displaced by a vessel floating in it, this weight being equal to the weight of the ship. Diminishing Stuff. — Planking worked under the SHIP BUILDING TERMINOLOGY 179 strakes and thinned to correspond with the thick- ness of the bottom plank. Dog-shore. — One of the two struts which hold the cradle of the ship from sliding on tlie slip-ways when the keel blocks are taken out. The lower end of each dog-shore abuts against tlie upper end of the ribband of the slip-way, and the upper end against the dog-cleat, which is bolted to the side of the bilge-way. Beneath each dog-shore is a small block called a trigger. In launching, the triggers are removed, the dog-shores knocked down, and the ship-cradle freed, so that, carrying the vessel, it slides down the slip-ways. A time- honored signal for launching is "Down dog- shores ! ' ' Double FuttocJcs. — Timbers in the cant-bodies extending from the deadwood to the run of the second futtock-head. Drift-piece. — One of the upright or curved pieces of timber that connect the plank-sheer with the gunwale. Dubbing. — Dressing a timber smooth witli the adze. Entering-port. — A port or opening cut in the side of the vessel to serve as a door of entrance. Expansion. — The expansion of the skin of a ship, or rather of a network of lines on that surface, is a process of drafting to facilitate the laying-off of the dimensions and positions of the planks of which that skin is to be made. Pair. — To make in true curves or proportions; 180 COURSE IN WOODEN BOAT AND SPIIP BUILDING to make regular, true, smooth, or flowing the lines of a boat or ship. False Keel. — A set of timbers worked onto the main or true keel out-board, and intended to pre- vent leeway, also to protect the true keel in case of grounding. Fay. — To fit close together, as two pieces of Avood or timber. Faying Surface. — The face or end of a piece of timber which joins another similar surface so closely as to leave no interstice. Filling. — Pieces of material or a composition fitted in between the frames of the hold, to in- crease the watertightness, resist conpression, and prevent the accumulation of dirt, bilge-water, and vermin. Blocks of wood, bricks, mortar, cement, and asphalt have been used. Flat. — One of a number of ship's frames of equal size and forming a straight middle body; also a timber which has no curves, as the floor- timbers of the dead-flat amidships. Floor. — The bottom part of the hold on each side of the keelson; the flat portion of a vessel's hold. Floor Timbers. — Cross timbers uniting the heels of two futtocks. Flush Deck. — A deck running the whole length of the ship, from stem to stern, without forecastle or poop. Forecastle. — (Pronounced foke'sl.) The part of a ship forward of the foremast; a forward part of the space below decks, for the accommodation SHIP BUILDING TKHMINOLOGY 181 of seamen; in flush decks, a part of the upper deck forward of the after fore shroud ; or a short upper deck forward. Forefoot. — The forward end of a vessel's keel, on which the stem-post is stepped. Fore-hook. — A strengthening piece in the stem, binding the bows together; also called a breast- hook. Foremast. — The mast nearest the bow in ves- sels carrying more than one mast. Frame. — A built-up rib of a wooden vessel. Two or more futtocks united form a frame. Frame Mould. — A pattern or template for the frame of a boat or ship. Freeboard. — That part of a vessel's side which is included between the plank-sheer and the water- line. Furring. — Double planking of a ship's side. Futtock. — One of the curved or crooked timbers in a built-up or compound rib or frame of a ves- sel. A timber of the dimensions and form for a frame of a ship cannot be procured in one piece ; the frame is built up of pieces scarfed together. The number required is according to the length of the sections of the requisite height. They are known as the first, second, or third futtock, ter- minated by the top-timber. The term futtock is also applied to the complete half of a frame. Futtock-plank. — The first plank of the ceiling next to the keelson; also called the limber-strake. 182 COURSE IX WOODEN BOAT AND SHIP BUILDING The first plank of the skin next to the keel is the garboard-strdke. Gallery. — A balcony projecting from the after part of a ship, as the quarter-gallery or stern- gallery. Galley. — 1. A clinker-built boat for ship's use, from 28 to 36 feet long, rowed by ten or twelve men. 2. The cook-house on board ship, which is on deck or in a forward part of the vessel. Gangway. — An opening in the bulwarks of a vessel by which persons come on board or dis- embark. Garhoard Strake. — The row or strake of planks nearest to the keel on the outside of a ship's bottom. The rabbet to receive the garboard strake is made along the upper edge of the keel. Ground Timbers. — The timbers which lie on the keel and are bolted to the keelson. Ground-icays. — The large blocks and planks which support the cradle on which a ship rests and is launched. Gunnale. — The upper planking covering the tim- ber heads around the topside of the ship ; also the piece of timber around the topside of a boat, and having rowlocks for the oars. Half-breadlh Plan. — A plan or top view of one- half of a ship divided by a vertical longitudinal section in the line of the keel. It shows the water lines, bow and buttock lines, and diagonal lines of construction. SHIP BUILDING TERMINOLOGY 183 Half -Floor. — One of the timbers of a frame, the heel of which is over the keel, while on its head rests the heel of the second futtock. It lies for half its length alongside the cross-timber, with the other half alongside the first futtock. Half-timber. — One of the short futtocks in a cant-frame. Harping. — A continuation of the ribbands be- yond the square frames, moulded to the shape of the hull and used for proper spacing of cants and futtocks. The term harpings is also applied to the plank wales of the bow, which are of extra strength. Also spelled harpin. Hatch. — An opening in a deck or floor, or the covering for the same. Hatchivay. — One of the large rectangular open- ings in the deck of a ship by which freight is hoist- ed in or out, and access is had to the hold. The coverings are hatches, and these are fastened down by battens. There are four pieces in the frame of a hatchway, including the coamings and head-ledges. The hatchways are called fore hatch, or main hatch, or after hatch, as the case may be, according to the size and character of the vessel. Haivsehole. — A hole in the bow through which a cable or hawser may be passed. In large ships the ha"\\'seholes are four in number. Hawse-piece. — One of the cant-frames standing next to the knightheads, and fitted close together, so as to form a solid mass of timber for the 184 COURSE IN WOODEN BOAT AND SHIP BUILDING passage of the liawselioles ; also a plank or strake on the ship's bow Avhich is pierced by the hawse- hole. Head. — 1. The fore part, beak, bow, or stem end of a vessel. 2. The upper part of a timber in a frame. The other end is the heel. 3. The forefoot of the keel. Heel. — The lower end of a timber in a frame; the after end of a ship 's keel. Hog-frame. — A fore-and-aft frame forming a truss in the main frame of a vessel, to assist in giving vertical rigidity to the structure. Hold. — The interior part of a ship, in which the cargo of a merchant vessel is stored. The por- tions are distinguished as the fore, main and after holds. Horn Timber. — A small timber to protect the end of the stern-post and to eliminate end wood. Hull. — The body of a ship or boat, exclusive of the masts, yards, sails, and rigging. Hurricane Deck. — A raised platform extending from side to side of a ship, above deck amidships ; a bridge or station for the officer in command. Inboard. — Inside a ship's hull. Inner Post. — A piece brought in at the fore side of the main post, and generally continued as high as the wing transom to seat the other transoms upon. Keel. — The lower longitudinal beam or mem- ber of the framework of a vessel, serving as the SHIP BUILDING TERMINOLOGY 185 backbone of the entire frame. When a ship is to be built the keel is first laid, upon blocks of which the upper surfaces form an angle of about three degrees with the horizon. These are called keel- blocks and are usually about three feet high and spaced about four feet apart. White oak is a favorite material for the keel. Keelson. — A beam running lengthwise above the keel, and bolted to the middle of the floor frames, binding them to the keel, in order to stiff- en the vessel. Knee. — Any one of the angular pieces of tim- ber or iron connecting the beams and the frames of a vesseh Knighthead. — One of the first cant timbers on each side of the stem, rising obliquely from the keel and passing on each side of the bowsprit, to secure its inner end. Limber. — A passage on each side of the keelson for bilge water. It is covered by a movable plank called a limber-board, the edges of which rest respectively upon the keelson and the limber strake. Limber Strake. — The strake of the inner skin of a ship which is nearest to the keelson. Lines {on a Drawing). — The principal lines of a ship plan or drawing are as follows : (a). Base Line. — A horizontal reference line from which vertical measurements are taken. (b). Center Line — A vertical line in the center of the body plan, perpendicular to the base line. 186 COURSE IN WOODEN BOAT AND SHIP BUILDING , A horizontal line on the half -breadth plan through the center of the vessel. (c). Diagonals — Lines running diagonally from the center line to frame lines. (d). Frame Lines — Outlines showing the shape of the frames of the vessel. (e). Water Lines — Horizontal lines parallel to the base line in the body plan; horizontal lines parallel to the base line in the sheer plan; curved lines in the half -breadth plan. Lines Plan. — A drawing showing the general outline or form of the vessel. The lines plan com- prises three plans ; (a). Sheer Plan — A side view showing the length of the vessel and heights of the sheer or gunwale. (b). Half -breadth Plan — A top view showing the horizontal or floor plan on any water lines. (c). Body Plan — An end view showing the curves of the sides or frame lines at any point in the vessel. Frame lines forward of the midship section are on the right of the center line; those aft of the midship section on the left of the center line. Load Water-line. — The line of flotation of a ship when it has its full cargo aboard. Loftsman. — A man who lays out and makes moulds for a vessel. Mast. — A long spar placed amidships, nearly perpendicularly upon the keelson, and serving to support yards, sails, and rigging, or in steam ves- SHIP BUILDING TERMINOLOGY 187 sels for signaling, hoisting, and other purposes. The lower end, or heel, of a mast rests in a step on the keelson. Mast-hole. — A framed hole in the deck to receive a mast. It is made of larger diameter than the mast by twice the thickness of the wedges which hold the mast in position. Mould. — A full-size pattern of the same figure and dimensions as the moulding-side of the piece which it represents. The mould may be of skeleton form and may serve for several frames. It is usually a thin plank cut to the form of a ship tim- ber and serves as a template for scribing the mem- bers for the workmen, Avho saw, hew, and adze them into shape. Moulding. — The depth or dimension (of a piece of timber) which lies in the moulding-plane. Moulding-edge. — That edge of a ship's frame, which comes in contact with the skin and is repre- sented in the plan. The other edge is the heveling- edge. Mould Loft. — A large open room on the floor of which drawings and moulds of a vessel are laid out full size. Planking. — The skin, or wooden covering of plank on the exterior and interior surfaces of the ribs or frames, and on the beams of a vessel. A line of planking is a strake, and is named from its position, as garboard strake, sheer strake, etc. Planking-clamp. — A clamp used for bending a 188 COURSE IN WOODEN BOAT AND SHIP BUILDING strake against the ribs or frames of a vessel and holding it until secured by bolts or treenails. Plank-sheer. — A plank resting on the heads of the top timbers of the frames or ribs ; the gunwale. Poop. — A short deck built over the after part of a vessel, also called poop-deck; the aftermost, highest part of the hull. Port. — 1. A framed opening in a ship's side, closed by glazed lids, called sidelights, or by water- tight shutters, called deadlights. An airport is an opening through the side below decks for ventila- tion. 2. The left side of a vessel to a person standing on deck and facing forward; formerly called lar- board. Port-hole. — An embrasure in a ship's side. Pump-well.- — A compartment extending from the ship's bottom to the lower or the upper deck, as the case may be, to contain the pump-stocks, etc. ; used to remove bilge water which collects in the limbers, or in the event of a leak. Quarter. — The side of a ship, aft, between the main channels and the stern. Quarter-decJc. — A deck raised above the waist and extending from the stern to the mainmast in a full-rigged ship. Rabbet. — The recess cut in the keel, stem, and stern to receive the ends of planking. Rail. — The top of the bulwarks of a ship. The part continued round the stern is the taft'rail. Rake. — The forward pitch of the stem of a SHIP BUILDING TERMINOLOGY 189 vessel, or the backward slope of tlie stern, that is, the degree in which it overhangs the keel. The rake of a rudder is that of the stern-post. Reaming-iron. — A blunt chisel used for opening the seams between the planking of a ship, before calking them with oakum. Rib. — One of the curved side timbers of a ship or boat, to which the wooden planking and the interior sheathing is treenailed or pinned. These frames are called libs from their resemblance in form and function to the ribs of the human body. They are fastened to the keel or backbone of a ship in much the same manner as the human ribs are articulated to the spine. For wooden vessels of considerable size, timber of the required dimen- sions and form cannot be procured to make a rib of one piece, so each rib or frame is made of sec- tions scarfed together. These sections are called futtocks. Ribband. — A temporary lengthwise strip follow- ing a vessel's curves and bolted to its ribs on the square body to hold them in place until they re- ceive the planking or plating. A number of these are fastened at different distances from the keel. Ribband Lines. — Oblique longitudinal sections of the hull. Ribband Shore. — A strut to support the frame- work of a ship while building. The head rests against the ribbands and the base on the slip or way. Rider. — A rib within the inner sheathing, bolted ISO COURSE IN WOODEN BOAT AND SHIP BUILDING through the latter into the main ribs and planking, for the purpose of stiffening the frame. The riders extend from the keelson to the orlop-deck beams. Riding -hitts. — Two strong upright timbers near the bows of a ship, to which the cable is secured ; they extend through two decks, are connected by a crosspiece, and braced against the strain of the cable by horizontal standards bolted to the deck beams. Rising-line. — A curved line on the plans of a ship, marking the height of the floor timbers throughout the length, and thereby fixing the sharpness and flatness of the vessel's bottom. , Risings. — Thick planks supporting the timbers of the decks. Rudder. — A contrivance, usually consisting of a flat frame, hung to the stern-post of a vessel, to afford a means of steering. The pintles of the rudder are hooked upon the eyebolts of the stern- post, thus giving an axis of oscillation as the rud- der is moved to and fro by the filler. Rudder-port. — The hole in a ship's counter for the passage of the rudder-head, or upper cylin- drical end. Scaling. — The process of developing the proper diminish of a plank fore and aft. Scantling. — The dimension or size prescribed for any part of the hull of a ship, especially the transverse dimension of pieces of timber. Scarf. — A lapped joint made by beveling off, SHIP BUILDING TERMINOLOGY 191 notching or otherwise cutting away the sides of two timbers at the ends, and bolting or strapping them together so as to form one continuous piece, usually without increased thickness. Also spelled scarph. Scupper.— A hole or tube leading through the ship's side, to carry away water from the deck. Scuttle. — A small opening in a ship's deck or side, closed by a shutter or hatch. Seam. — The space between two planks of a ship 's skin, made water-tight by calking. Shaft-alley. — A passageway between the after bulkhead of the engine room and the shaft-pipe, around the propeller shaft and affording a means of access thereto. Shaft-log. — A member of the stern of a wooden vessel through which the propeller-shaft passes. Shaft-pipe. — The pipe or tube in the stern of a vessel through which the propeller-shaft passes in- board. It occupies a hole bored through the stern- post and deadwood. Sheathing.- — A covering, usually thin plates of copper or of an alloy containing copper, to protect a ship's bottom. Sheer. — The rise or upward curvature of the lines of a vessel 's hull toward the bow and stern. Sheer-line. — The line of the deck at the side of the ship. Sheer Plan.—^\iQ plan of elevation of a ship, showing the outboard features of the vessel, lines of stem and stern, strakes, water lines, etc., also 192 COURSE IN WOODEN BOAT AND SHIP BUILDING the hang of each deck inside. A vertical, longi- tudinal midship section of a vessel, on which are shown the features similar to those of an arch- itectural elevation, including water lines, level lines, diagonal lines, buttock and bow lines, the topside line, the cutting-down line, etc. Sheers. — An apparatus, usually mounted on a wharf, for placing the masts in a ship, hoisting in and taking out boilers, etc. It consists of two masts, or legs, secured together at the top, and provided with ropes or chains and pulleys for hoist- ing purposes. Sheer Strake. — The strake under the gunwale in the topside of a vessel. It is generally worked thicker than the rest of the topsides, and is scarfed between the drifts. Shore. — One of the wooden props by which the framework of a vessel is externally supported Avhile building ; or by which the vessel is laterally supported on the stocks. Siding. — Dressing the timbers of a ship to the required thickness ; also the timbers so dressed. The thickness of a timber in a direction perpen- dicular to the moulding plane. Skeg. — A knee which unites and braces the stern-post and keel of a boat. Skin. — The inner or outer planking of a ship. The inner skin is commonly called the ceiling. Sliding-way. — One of the structures on each side of and parallel with the keel, supporting the bilgeways of the cradle on which the vessel rests SHIP BUILDING TERMINOLOGY 193 in launching. The sliding-ways are the inclined planes down which the vessel slides, and are made of narrow planks laid on blocks of wood. Slip. — An inclined plane on which a vessel in its cradle is supported Avhile on the stocks building, or upon which it is handled for repairs. Sny. — The trend of the lines of a ship upward from amidships toward the bow and the stern; a gentle bend in timber curving upward. Snying. — Curved planking set edgewise in the frame of a vessel at the bow or stern. Spiling. — The edge-curve of a plank or of a strake in a vessel's hull. Spiling Batten. — A batten on which shapes of planking, or other scantlings, are laid out to proper shape. Spilings. — Dimensions taken from a straight- edge or rule to different points on a curve. Stancliion. — A post for supporting the deck- beams of a vessel. Standard Knee. — A bent timber having one branch fastened against the upright side of a beam and the other against the ship's side. One fayed vertically to the vessel's side, above or beneath a beam, is called a hanging knee. Starboard. — The right-hand side of a vessel, looking from aft forward; in contradistinction to port, the left-hand side, formerly called larboard. Stem. — The foremost boundary of a vessel, be- ing a nearly vertical continuation of the keel, into which the lower end is scarfed. The forward ends 194 COURSE IX WOODKN BOAT AND SHIP BUILDING of the various strakes are united to the stem, and its advanced edge is the cutwater. Stem-knee. — A knee at the junction of the stem with the keel. Stemson. — A knee-piece with its horizontal arm scarfed to the keelson and its vertical arm fayed into the throats of the transoms. Step. — The recessed block in which the foot of a mast is placed. Stern. — The after part of a vessel, from the taff- rail down to the junction of the stern-post with the keel. Stern-knee. — A knee uniting the stern-post and the keel. Stern-post. — A slightly raking straight piece, rising from the after end of the keel. Stern-sheets. — That part of a boat between the stern and the aftermost thwart. Stemson. — A binding-piece above the deadwood in the stern, and practically forming an extension of the keelson, on which the stern-post is stepped. Stocks. — The framework of blocks and shores on which a vessel is built. It slopes gently down toward the water, and is usually a timber frame which, as the work of construction proceeds, as- sumes the form of a cradle. This rests on ways, on which it eventually slides, bearing the vessel into the water at launching. The vessel is sup- ported laterally by shores, Avhile the cradle is held by struts and chocks. In launching the ship, the shores are removed, so that the vessel rests al- SHIP BUILDING TERMINOLOGY 195 together in the cradle ; the ways are greased, the struts are knocked away, the chocks knocked out, and the vessel slides down the ways into the water, where the cradle becomes detached and floats clear of the ship. Stopwater. — A piece of wood driven into a hole at a scarf joint in a vessel's timber to render it watertight. Strake. — A breadth of planking or plating, especially one continuous from stem to stern on a vessel's hull. Strakes are named as follows : (a). Binding Strake — The first plank directly below the upper strake and generally installed in one length if material permits. (b). Bilge Strake — A strake passing over a vessel's bilge. (c). Broad Strakes — All planks below the shut- ter strake and the garboard strake. (d). G-arboard Strake — The extreme lower plank, next to the keel. (e) . Sheer or Upper Strake — The extreme upper plank. (f). Shutter Strake — The last plank of the bot- tom to be installed. (g). Lower Strakes — All planks below the bind- ing strake and above the shutter strake. Stringer. — An inside strake of plank, secured to the ribs and supporting the ends of the beams ; a shelf-piece. Surmark. — 1. A mark drawn on ship timbers at the intersection of the moulding edge with the rib- 196 COURSE IN WOODEN BOAT AND SHIP BUILDING band line ; tlie stations of the ribbands and harp- ings being marked on the timbers. 2. A cleat temporarily placed on the outside of a rib, to give a hold to the ribband by which, through the shores, it is supported on the slip-way. Taffrail. — The uppermost part of a ship's stern; the rail or topside of the bulwarks around the stern. Topside. — The upper part of a ship 's side. Topside Line. — A sheer line drawn above the top timber at the upper side of the gunwale. Top-timber. — The timber next above the futtocks in a built-up frame or rib. Top Breadth. — A line in the sheer plan drawn to the sheer of the ship fore and aft, at the height of the under side of the gunwale amidships. Transom. — A beam bolted across the stern-post, supporting the after end of a deck and giving shape to the stern. Transom-knee. — A knee bolted to a transom and after-timber. Treenail. — A cylindrical pin of hardwood, used for securing planking to the frames, or parts to each other. Treenails are from 1 to l-''4 inches in diameter, and are tightened in their places by wedges driven into each end. Trimming. — The final shaping of ship timbers, etc., after the rough shaping has been done ; also called forming. Waist. — The middle portion of a ship's deck, between the forecastle and the quarter-deck. SHIP BUILDING TERMINOLOGY 19T Wale. — A wide plank at certain portions of a ship's side, extending from stem to stern and fol- lowing the curve of the strokes. The various wales are known as the gumvale, main-wale, clian- nel-ivale, etc. Water Lines. — The lines of a ship drawn parallel with the surface of the water, at varying heights. In the sheer plan they are straight and horizontal ; in the half -breadth plan they show the form of the ship at the successive heights marked by the water lines in the sheer plan. Way or Ways. — The timber sills or track upon which a ship is built, and upon which she slides into the water in launching. INDEX Adze, plain 166, 16V lipped 166, 167 Angles for beveling frames 56 Applying mould to ship timbers 105 Apron 26 Assembling platform 109, 124, 125 showing diagonals 125 showing ways and square framing 124 Auger bits, ship 168, 169 Axe, broad 166, 168 Batten, spiling 71 Battens, use of 24, 25, 69, 71, 76 bending 34 Bearding line 33 Bending battens 34 frames for strap-frame boat 65 timbers 49, 51 Bevel and edging machines 110 Beveling angles 56 frames 53 board 55 for planking 79 ship frames on band saw 106 Bevels on diagonals, meth- od of developing 52 on each diagonal 54 Bilge planking 148 strake 68 Binding strake 68, Vl sealing for 74 Bits, auger 168, 169 Board, beveling 55, 56 Boat construction 17-83 false frames for 57, 59 manufactured frame. 57, 61 built-up frame 57, 62 strap frame 57, 64 Boat deck 158 Boat timbers, sawing.... 48 Body plan, boat 17, 19, 25, 52 standard wooden steam- ship 94, 95 Bolting ship frames 129 Boring through shaft log. 39 Bottom planking 148 Bow construction, ship.... 140 Bow lines 172 Bow of ship, ready for planking 138 planked 139 Box, steam 45-48 Bridge deck 160 Broad axe 166, 168 Brush, seam 83 Building-slip 172 Built-up frame construc- tion 57, 62 Bulkhead 172 Buttock-lines 173 Calking, boat 80-83 ship 154, 173 practice, form for... 80, 81 Calking irons 168, 169 mallet 168, 169 Camber 174 Cant frames 127 looking forward, show- ing heels of timbers. . 132 looking aft 133 looking forward, showing heads of timbers 133 looking aft 134 Cargo carrier, standard wooden 85 Carlings 176 199 200 INDKX Carriages, mill floor.. 106, 108 Ceiling 174 beveled without hand tools 122 Cementing seams 154 Chock 17.5 Clamps and wedges 144 Clinker-built 175 Coamings 176 Condensation pipe for steam box 48 Construction, ship 84 stem and stern (boat) . . 26 Cotton, calking with 81 Cradle 176 Cross spalls 57 Cutting a timber on band saw 107 heavy timber at an an- gle 114, 115 out the stock 33 rabbets 38 Deadwood 177 stem 26 stem 29 Beck, poop 150 Deck iron 168 Decks 177 Degrees on beveling board 55 Detail of boat stem 27 of stern 28 of form for practice calking 81 of rabbet through stem 37 Development of rabbet... 36 Diagonal-liuilt 178 Diagonal lines 52, 53, 54 Diagonals, bevels on. . .52, 54 projection of 63, 66 Dimensions, standard wooden steamship 87 Dog-shore 179 Drawings, ship 85 Dumb-iron 168, 169 Engine foundation, stand- ard wooden steamship 103 Erecting stem 38 Fairing-in a line 21 Tairing-up 63, 132 moulds 35 False frames 57, 59 keel 180 Fastening frames 125 Faying l^nees 113, 118 surface 180 Filling-in pieces 63 Finished timber 116 Finishing, boat 83 ship 154 Fitting frames 125 futtocks to ribbands. .. . 59 Floor timbers, boat 60 Forecastle 180 deck 161 section, standard wood- en steamship 103 Form for practice calk- ing 80, 81 for steam bending 49 Frame construction 57 Frames 41 bending, for strap-frame boat 65 boat, installing 59 boat, raising 60 cant ". 127 fitting and fastening... 125 in position to raise 129 ship 100 ship, beveling 106 ship, bolting 129 ship, raising 127, 130 raised 131 Framing platform 148 Freeboard 181 Futtock 181 Futtock moulds 41 forward 42 aft 43 Futtocks and frames 41 Futtocks, fitting to rib- bands 59 shape of 41-43 Galley 182 Garboard strake 40, 68, 69, 75, 182 INDKX 201 Guard 69 Gun house, top of 159 Half -breadth plan, boat. 17, 24 standard wooden steam- ship 87, 93 Hand tools 165 Handling heavy timbers in the yard 112 Harpings 60, 183 Hawsehole 183 Hog-frame 184 Horn timber 29 Hurricane deck 184 Inboard profile of standard wooden steamship. . . . 155 Installing boat frames .... 59 keelson 135 Interior of hull, looking aft 147 Iron strapping of hull. . . . 134 Irons, calking 168, 169 Keel 40, 184 scarfing 40 lock scarfs for 40 rabbet in 40 station lines on 38, 40 record, laid in ten min- utes 123 Keelson 185 boat 63 timbers 132 installing 135 and timber chute 136 Knees, surfacing 113, 117 faying 113, 118 Knighthead 185 Labor-saving devices 110 Launching ways 108 Laying off lines 20 Laying out the sheer line. 23 Layout of the ship 138 on mould loft floor 20 Limber strake 185 Line of shaft 40 Lines, fairing in 21 picking up the.,. 29, 82, 44 Lines, moulded — sheer plan 18 half -breadth plan 18 body plan 19 Lines on a drawing 185 Lines plan 186 Lining in 34 Loft, mould 17, 53 Lofting the ship 97 Lof tsnian 186 Lower stem 26 Lower strake, first, spiling for 73 Lower strakes 68, 76 scaling for 77 Machines and labor-saving devices 110 Machines, bevel and edg- ing 110 Making-iron 168, 169 Mallet, calking 168, 169 Manufactured frame con- struction 57, 61 Masts, shaping the. . . .151, 157 Materials and processes, ship construction 84 Midship construction sec- tion, standard wooden steamship 98, 99 Mill floor carriages. . .106, 108 Model for taking off off- sets 19 Mould 187 applying the 105 Moulded lines — sheer plan 18 half -breadth plan 18 body plan 19 Moulding 69 Mould loft. ...17, 53, 104, 187 work 20 Mould loft floor 21 picking up lines from.29, 32 Moulds, fairing up 35 futtock 41 f uttock, forward 42 aft 4-5 material for 33 202 INDJDX Moulds, sliip 97 boat, for stem 30 for stern 31 Navigating bridge 156 Oakum, calking with 81 Offsets, tables of 22, 23, 90, 91, 92 for wooden boat 22, 23 for ship — half -breadths. 92 for ship — heights above base 90 for ship — diagonals -91 Offsets, taking off 19 Outside planking 68 Painting, boat 83 ship hull 154 Picking up the lines from mould loft floor 29, 32 with flexible steel tem- plate 44 Pipe details of steam box. 46 Planing planking 83 Planking and finishing... 138 Planking, beveling for... 79 of stern, vertical. . .144, 146 of bottom, bilge, and side 148 outside 68 preparations for 139 Plans, sheer 17, 18, 22 half -breadth 17, 18, 24 body 17, 19, 25 ship 85 Platform, assembling 109,124, 125 framing 148 Poop deck.. 159, 188 framing the 150 completed 150 Poop section, standard wooden steamship. . . . 101 Processes, ship construc- tion 84 Profile of wooden steam- ship, inboard 155 Projection of diagonals. 63, 66 Propeller shaft, boring through shaft log for. 39 Putty, filling boat seams with 83 Eabbet, detail of 37 development of, through stem 36 in stem and stern 33 Rabbeting 33 Eabbet line, stem 36 Rabbets, cutting 38 Raising boat frames 60 ship frames 127, 130 the rudder 157 Rib 189 Ribbands 51, 60, 189 boat, fitting futtocks to. 59 running 61 Rising-line 190 Rudder, raising the. . .151, 157 Rudder stock, finished. . . . 121 shape after sixteen cuts. 120 working 113, 119 Running ribbands 61 Sandpapering planking... 83 Sawing and handling large timbers 110 boat timbers 55, 58 Sawmill floor carriages. . . 106, 108 Scaling 78, 190 for sheer strake 70, 72 for binding strake ... 72, 74 for lower strakes 77 Scantling 190 Scantlings of standard wooden steamship. ... 93 Scarf 190 Scarfing timber with an adze 167 Scupper 191 Seam brush 83 Seams, cementing 154 Sectional carriages for handling heavy tim- bers 108 Section through boat stem, showing development of rabbet 36 INDJfiX 203 midship eonstruetion sec- tion, standard wooden steamship 98, 99 from bridge deck to top • of wheelhouse 100 through poop 101 through engine founda- tion, looking forward . 102 through shaft tunnel, looking aft 103 through the forecastle. . 103 through engine room. . . . 162 through boiler room. . . . 163 Sections, laying down in. . 21 Setting up the keel 123 Shaft log 29, 40 boring through 39 Shaft tunnel, standard wooden steamship. . . . 102 Shaping rudder stock 119 the masts 157 Sheathing 68 Sheer 191 Sheer line, laying out the. 23 Sheer plan 17,18,22,191 standard' wooden steam- ship 88, 89! Sheer strake 68, 69 scaling for 70 Sheers . . 192 Ship bow construction, close-up view of 140 Ship construction 84-169 drawings and plans .... 85 specifications 85 moulds 97 frames 100 frames, beveling 106 frames on tracks 128 auger bits 168, 169 Shipfitting 154 Shipyard, panoramic view of 152, 153 Shipvards and ways 157 Shore 192 Shutter strake 68 Side planking 148 Siding 192 Sirmark (Surmark) 195 Skeg 192 Skin 68 Snying 193 Spalls, cross 57 Special beveling machine. 110 Specifications, ship 85 Spiling 71 for sheer and binding strakes 72 for first lower strake.. 73 Spiling batten 71 Spilings 193 Standard wooden steam- ship 85 sheer plan — stem 88 sheer plan — stern 89 offsets, half -breadths. ... 92 dimensions 87 half -breadth plan 87, 93 body plan 87,94, 95 midship construction section 87, 98, 99 offsets, heights above base 90 offsets, diagonals 91 scantlings 96 section from bridge deck to top of wheelhouse. 100 section through poop... 101 section through engine foundation 102 section through shaft tunnel 102 section through forecas- tle 103 inboard profile 155 wheelhouse and navigat- ing bridge 156 top of wheel house 157 boat deck 158 top of gun house 159 poop deck 159 bridge deck 160 forecastle deck 161 section through engine room 162 section through boiler room 163 plan view at dynamo flat 164 Station lines 20 204 INDEX Steam bending 49 form for 51 Steam box 46, 144 details of 45,46, 47, 48 Steel template, flexible. 41, 44 Stem 26 detail of 27 moulds 29 Stem and stern construc- tion 26 Stemson 194 Stern 26 detail of 28 moulds 29 Stern post 26 Stern post knee 29 Stern of ship, showing vertical planking. . . . 146 Sternson 194 Stock, cutting out 33 Stocks 194 Stopwaters 40 Strakes 68, 195 to find the width of... 69 Strap-frame boat construc- tion 57, 64 Strapping, iron, of hull. . . 134 Surfacing knees 113, 117 Surmarks (or Sirmarks).46, 195 Table of offsets, boat 22, 23 ship 90, 91, 92 Taffrail 196 Taking off offsets, model for 19 Templates 37 flexible steel 41, 44 Terminology 170-197 Tieing ends of boat frames 57 Timber chute ,,,... 136 Timber, cutting on band saw 107 heavy, cutting at an an- gle 114, 115 sawing heavy Ill Timbers, boat floor 60 ship, laying out 105 handling heavy 112 Tools, hand 165 Topside 196 Transom 29, 196 Treenails 149, 196 Upper strake 68 Vertical planking of stern 144, 146 Wall 197 Water lines 186, 197 Water seal trap for steam box 47, 48 Ways, ship 107, 152, 197 lowered while ship was in frame 131 Wheel house 156 top of 157 Wooden boat and ship ter- minology 170-197 Wooden ship, framed up complete 141 partially planked 142 planked ready for launching 143 finished 145 interior of hull 147 ready to launch 149 Wooden steamship, stand- ard 85, 161 DRAKE'S MECHANICAL BOOKS ♦Title style 1 Price Carpentry and Building Books Modern Carpentry. Two volumes . Cloth $2.00 Modern Carpentry. Vol. I Cloth 1.00 Modern Carpentry. Vol. II Cloth 1.00 The Steel Square. Two volumes . . Cloth 2.00 The Steel Square. Vol. I Cloth 1.00 The Steel Square. Vol. II Cloth 1.00 A. B. C. of the Steel Square Cloth .50 A Practical Course in Wooden Boat and Ship Building "Cloth 1.50 Common Sense Stair Building and Handrailing Cloth 1.00 Modern Estimator and Contrac- tor's Guide »Cloth 1.50 Light and Heavy Timber Framing Made Easy Cloth 2.00 Builders' Architectural Drawing Self-taught Cloth 2.00 Easy Steps to Architecture Cloth 1.50 Five Orders of Architecture Cloth 1.50 Builders' and Contractors' Guide Cloth 1.50 Practical Bungalows and Cottages •Cloth LOO Low Cost American Homes •Cloth 1.00 Practical Cabinet Maker and Fur- niture Designer Cloth 2.00 Practical Wood Carving Cloth 1.50 Home Furniture Making Cloth .60 Concretes, Cements, Mortars, Plas- ters and Stuccos Cloth 1.50 Practical Steel Construction Cloth .75 Practical Bricklaying Self-taught. Cloth 1.00 Practical Stonemasonry Cloth 1.00 Practical Up-to-date Plumbing. . . . Cloth 1.50 Hot Water Heating, Steam and Gas Fitting ' "Cloth 1.50 Practical Handbook for Mill- wrights Cloth 2.00 Boat Building for Amateurs Cloth s are ma 1.00 NOTE. — New Books and Revised Edition rked* ^ DRAKE'S MECHANICAL BOOKS ♦Title 1 Style Price Steam Engineering Books Swingle's Handbook for Steam Engineers and Electricians .... "Lea. $3.00 Steam Boilers, Construction, Care and Operation *Lea. 2.00 Complete Examination Questions and Answers for Marine and Stationary Engineers *Lea. 2.00 Swingle's Catechism of Steam, Gas and Electrical Engineering. *Lea. 1.50 The Steam Turbine, Its Care and Operation Cloth 1.00 Calculation of Horse Power Made Easy Cloth .75 Railroad Books Modern Locomotive Engineering . "Lea. $3.00 Locomotive Fireman's Boiler In- structor *Lea. 1.50 Locomotive Engine Breakdowns and How to Repair Them "Lea. 1.50 Operation of Trains and Station Work *Lea. 2.00 Construction and Maintenance of Railway Roadbed and Track. . . Lea. 2.00 First, Second and Third Year Standard Examination Ques- tions and Answers for Locomo- tive Firemen *Lea. 2.00 Complete Air Brake Examination Questions and Answers *Lea. 2.00 Westinghouse Air Brake System. Cloth 2.00 2.00 Walschaert Valve Gear Break- downs Cloth 1.00 NOTE. — New Books and Revised Editions are marked* 1 h. J DRAKE'S MECHANICAL BOOKS ♦Title I Style I Price Electrical Books Electrical Tables and Engineering Data 'Lea. $1.50 Electrical Tables and Engineering Data •Cloth 1.00 Motion Picture Operation 'Lea. 1.50 Motion Picture Operation *Cloth 1.00 Alternating Current Lea. 1.50 Alternating Current Cloth 1.00 Wiring Diagrams and Descrip- tions *Lea. 1.50 Wiring Diagrams and Descrip- tions 'Cloth 1.00 Armature and Magnet Winding. .*Lea. 1.50 Armature and Magnet Winding. .* Cloth 1.00 Modern Electric Illumination. .. .*Lea. 1.50 Modern Electric Illumination 'Cloth 1.00 Modern Electrical Construction . . 'Lea. 1.50 Modern Electrical Construction. .'Cloth 1.00 Electricians' Operating and Test- ing Manual 'Lea. 1.50 Electricians' Operating and Test- ing Manual 'Cloth 1.00 Drake's Electrical Dictionary. . . . Lea. 1.50 Drake's Electrical Dictionary.... Cloth 1.00 Electric Motors, Direct and Alter- nating 'Lea. 1.50 Electric Motors, Direct and Alter- nating 'Cloth 1.00 Electrical Measurements and Me- ter Testing Lea. 1.50 NOTE. — New Books and Revised Editions are marked* DRAKE'S MECHANICAL BOOKS •Title 1 style 1 Price Electrical Books — Continued Electrical Measurements and Me- ter Testing Cloth $1.00 Lea. 1.50 Drake's Telephone Handbook Drake's Telephone Handbook. . . . Cloth 1.00 Elementary Electricity, Up-to- Date •Cloth •Cloth 1.25 1.00 Electricity Made Simple Easy Electrical Experiments •Cloth LOO Wireless Telegraph and Telephone Handbook Cloth 1.00 Telegraphy, Self-taught Cloth 1.00 Dvnamo-Electric Machines Cloth 1.50 Electro-Plating Handbook Lea. 1.50 Electro-Plating Handbook Cloth 1.00 Modern American Telephony Lea. 2.00 Handy Vest-Pocket Electrical Dic- tionary Lea. .50 Handy Vest-Pocket Electrical Dic- tionary Cloth .25 Storage Batteries Cloth .50 Elevators — HydrauKc and Electric Cloth 1.00 How to Become a Successful Mo- torman Lea. 1.50 Motorman's Practical Air Brake Instructor Lea. 1.50 Electric Railway Troubles Cloth 1.50 Electric Power Stations Cloth 2.50 Electrical Railroading Lea. 3.50 s are marked* NOTE. — New Books and Revised Edition \._ -^ j; 9. J I